- 您現在的位置：買賣IC網 > PDF目錄365450 > S71WS512N80BAEZZ2 (Spansion Inc.) Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt PDF資料下載
參數資料
| 型號： | S71WS512N80BAEZZ2 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| 中文描述： | 堆疊式多芯片產品（MCP）的閃存和移動存儲芯片的CMOS 1.8伏特 |
| 文件頁數： | 63/142頁 |
| 文件大?。?/td> | 1996K |
| 代理商： | S71WS512N80BAEZZ2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁當前第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁
June 28, 2004 S71WS512NE0BFWZZ_00_A1
S29WSxxxN MirrorBit Flash Family For Multi-chip Products (MCP)
63
A d v a n c e I n f o r m a t i o n
Once the Password is written and verified, the Password Mode Locking Bit must
be set in order to prevent verification. The Password Program Command is only
capable of programming “0”s. Programming a “1” after a cell is programmed as
a “0” results in a time-out by the Embedded Program Algorithm with the cell
remaining as a “0”. The password is all F’s when shipped from the factory. All 64-
bit password combinations are valid as a password.
The Password Verify Command is used to verify the Password. The Password is
verifiable only when the Password Mode Locking Bit is not programmed. If the
Password Mode Locking Bit is programmed and the user attempts to verify the
Password, the device will always drive all F’s onto the DQ data bus.
The lower two address bits (A1–A0) are valid during the Password Read, Pass-
word Program, and Password Unlock.
The Password Unlock command is used to clear the PPB Lock Bit so that the PPBs
can be unlocked for modification, thereby allowing the PPBs to become accessible
for modification. The exact password must be entered in order for the unlocking
function to occur. This command cannot be issued any faster than 1 μs at a time
to prevent a hacker from running through all the 64-bit combinations in an at-
tempt to correctly match a password. If the command is issued before the 1 μs
execution window for each portion of the unlock, the command will be ignored.
The Password Unlock function is accomplished by writing Password Unlock com-
mand and data to the device to perform the clearing of the PPB Lock Bit. The
password is 64 bits long. A1 and A0 are used for matching. Writing the Password
Unlock command does not need to be address order specific. An example se-
quence is starting with the lower address A1–A0= 00, followed by A1–A0= 01,
A1–A0= 10, and A1–A0= 11.
Approximately 1 μSec is required for unlocking the device after the valid 64-bit
password is given to the device. It is the responsibility of the microprocessor to
keep track of the 64-bit password as it is entered with the Password Unlock com-
mand, the order, and when to read the PPB Lock bit to confirm successful
password unlock. In order to re-lock the device into the Password Mode, the PPB
Lock Bit Set command can be re-issued.
The
Password Protection Command Set Exit
command must be issued after
the execution of the commands listed previously to reset the device to read
mode. Otherwise the device will hang.
Note that issuing the
Password Protection Command Set Exit
command re-
enables reads and writes for Bank 0.
Non-Volatile Sector Protection Command Set Definitions
The Non-Volatile Sector Protection Command Set permits the user to program the
Persistent Protection Bits (PPBs), erase all of the Persistent Protection Bits (PPBs),
and read the logic state of the Persistent Protection Bits (PPBs).
The
Non-Volatile Sector Protection Command Set Entry
command se-
quence must be issued prior to any of the following commands to enable proper
command execution.
PPB Program Command
All PPB Erase Command
PPB Status Read Command
Note that issuing the
Non-Volatile Sector Protection Command Set Entry
command disables reads and writes for the bank selected. Reads within that
相關PDF資料 |
PDF描述 |
|---|---|
| S71WS512N80BAEZZ3 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ0 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ2 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ3 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAWZZ0 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71WS512N80BAEZZ3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAWZZ0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
發布緊急采購，3分鐘左右您將得到回復。