參數資料
型號： S5T8701
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： FLEX ROAMING DECODER II
中文描述： FleX創建漫游解碼器二
文件頁數： 49/70頁
文件大?。?/td> 506K
代理商： S5T8701
S5T8701
FLEX
TM
ROAMING DECODER II
49
c:
Current system cycle number. This value is updated every frame regardless of whether the
S5T8701 needs to decode the frame. This value will change to its proper value for a frame at
the end of block 0 of the frame. The value of these bits is not guaranteed when
FIV
is 0.
SMU:
Synchronous Mode Update. Set if the SM bit has been updated in this packet. When the S5T8701
is turned on, this bit will be set when the first synchronization words are found (SM changes to 1) or
when the first synchronization search window after the S5T8701 is turned on expires (SM stays 0).
The latter condition gives the host the option of assuming the paging device is in range when it is
turned on, and displaying out-of-range only after the initial A search window expires. After the initial
synchronous mode update, the SMU bit will be set whenever the S5T8701 transitions from/to
synchronous mode. Cleared when read. Changes in the SM bit due to turning off the S5T8701 will
not cause the SMU bit to be set. This bit is initialized to 0 when the S5T8701 is reset.
LBU:
Low Battery Update. Set if the value on two consecutive reads of the LOBAT pin yielded different
results. Cleared when read. The host controls when the LOBAT pin is read via the Receiver Control
Packets. Changes in the LB bit due to turning on the S5T8701 will not cause the LBU bit to be set.
This bit is initialized to 0 when the S5T8701 is reset.
MT:
Minute Time-out. Set if one minute has elapsed. Cleared when read. This bit is initialized to 0 when
the S5T8701 is reset.
EOF:
End Of Frame. Set when the S5T8701 is in all frames mode and the end of frame has been
reached. The S5T8701 is in all frames mode if the all frames mode enable counter is non-zero, if
any temporary address enabled counter is non-zero, or if the FAF bit in the All Frame Mode Packet
is set. Cleared when read. This bit is initialized to 0 when the S5T8701 is reset.
EA:
End of Addresses. If EAE of the control packet is set and an address is detected in a frame, EA will
be set after the S5T8701 processes the last address in the frame. Since data packets take priority
over the status packet, the status packet with the EA bit set is guaranteed to come after all address
packets for the frame. Cleared when read. This bit is initialized to 0 when the S5T8701 is reset.
BOE:
Buffer Overflow Error. Set when information has been lost due to slow host response time. When
the data packet FIFO transmit buffer on the S5T8701 overflows, the S5T8701 clears the transmit
buffer, turns off decoding by clearing the ON bit in the Control Packet, and sets this bit. Cleared
when read. This bit is initialized to 0 when the S5T8701 is reset.
x:
Unused bits. The value of these bits is not guaranteed.
相關PDF資料
PDF描述
S5T8702 FEEX ALPHANUMERIC DECODER II
S5T8702X01-E0R0 FEEX ALPHANUMERIC DECODER II
S5T8803A01-D0B0 DIODE ZENER SINGLE 500mW 30Vz 4.2mA-Izt 0.05 0.1uA-Ir 23 SOD-123 3K/REEL
S5T8803A01-S0B0 DIODE ZENER SINGLE 200mW 30Vz 4.2mA-Izt 0.05 0.1uA-Ir 23 SOD-323 3K/REEL
S5T8803A 10 CH PLL
相關代理商/技術參數
參數描述
S5T8701X01-E0R0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLEX ROAMING DECODER II
S5T8702 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FEEX ALPHANUMERIC DECODER II
S5T8702X01-E0R0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FEEX ALPHANUMERIC DECODER II
S5T8803A 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:10 CH PLL
S5T8803A01-D0B0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:10 CH PLL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*