- 您現在的位置：買賣IC網 > PDF目錄365429 > S5T8701 (SAMSUNG SEMICONDUCTOR CO. LTD.) FLEX ROAMING DECODER II PDF資料下載
參數資料
| 型號： | S5T8701 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | FLEX ROAMING DECODER II |
| 中文描述： | FleX創(chuàng)建漫游解碼器二 |
| 文件頁數： | 19/70頁 |
| 文件大?。?/td> | 506K |
| 代理商： | S5T8701 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
S5T8701
FLEX
TM
ROAMING DECODER II
19
EAE:
End of Addresses Enable. When this bit is set, the EA bit in the Status Packet will be set
immediately after the S5T8701 decodes the last address word in the frame if there was any
address detected in the frame. When this bit is cleared, the EA bit will never be set.
ON:
Turn On Decoder. Set if the S5T8701 should be decoding FLEX signals. Clear if signal processing
should be off (very low power mode). If the
ON
bit is changed twice and the control packets making
the changes are received within 2ms of each other, the S5T8701 may ignore the double change
and stay in its original state (e.g. if it is turned off then on again within 2ms it may stay on and
ignore the off pulse). Therefore it is recommended that the host insures a minimum of 2ms between
changes in the
ON
bit. (value after reset=0)
NOTES:
Turning off the S5T8701 must be done using the following sequence. This sequence is performed automatically by
the FLEX stack software version 1.2 and greater.
1. Turn off the S5T8701 by sending a Control Packet with the
ON
bit cleared.
2. Turn on the S5T8701 by sending a Control Packet with the
ON
bit set.
3. Turn off the S5T8701 by sending a Control Packet with the
ON
bit cleared.
Timing between these steps is specified below and is measured from the positive edge of the last clock of one
packet to the positive edge of the last clock of the next packet:
The minimum time between steps 1 and 2 is 2ms or the programmed shut down time, whichever is greater.
The programmed shut down time is the sum of all the of the times . programmed in the used Receiver Shut
Down Settings Packets.
There is no maximum time between steps 1 and 2.
The minimum time between steps 2 and 3 is 2ms.
The maximum time between steps 2 and 3 is the programmed warm up time minus 2ms. The programmed
warm up time is the sum of all the of the times programmed in the used Receiver Warm Up Settings
Packets.
相關PDF資料 |
PDF描述 |
|---|---|
| S5T8702 | FEEX ALPHANUMERIC DECODER II |
| S5T8702X01-E0R0 | FEEX ALPHANUMERIC DECODER II |
| S5T8803A01-D0B0 | DIODE ZENER SINGLE 500mW 30Vz 4.2mA-Izt 0.05 0.1uA-Ir 23 SOD-123 3K/REEL |
| S5T8803A01-S0B0 | DIODE ZENER SINGLE 200mW 30Vz 4.2mA-Izt 0.05 0.1uA-Ir 23 SOD-323 3K/REEL |
| S5T8803A | 10 CH PLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S5T8701X01-E0R0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLEX ROAMING DECODER II |
| S5T8702 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FEEX ALPHANUMERIC DECODER II |
| S5T8702X01-E0R0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FEEX ALPHANUMERIC DECODER II |
| S5T8803A | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:10 CH PLL |
| S5T8803A01-D0B0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:10 CH PLL |
發(fā)布緊急采購，3分鐘左右您將得到回復。