- 您現在的位置：買賣IC網 > PDF目錄192300 > S29GL064A10BAIW12 (SPANSION LLC) 4M X 16 FLASH 3V PROM, 100 ns, PBGA64 PDF資料下載
參數資料
| 型號： | S29GL064A10BAIW12 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 4M X 16 FLASH 3V PROM, 100 ns, PBGA64 |
| 封裝： | FBGA-64 |
| 文件頁數： | 55/97頁 |
| 文件大?。?/td> | 3490K |
| 代理商： | S29GL064A10BAIW12 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
January 11, 2006 S29GL-A_00_A5
S29GL-A MirrorBit Flash Family
57
Pr el im i n a r y
DQ7 or DQ6 status bits, just as in the standard program operation. See Write
Operation Status on page 63 for more information.
The system must write the Program Resume command (address bits are don’t
care) to exit the Program Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ignored. Another Program
Suspend command can be written after the device resumes programming.
Figure 5. Program Suspend/Program Resume
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is ini-
tiated by writing two unlock cycles, followed by a set-up command. Two
additional unlock write cycles are then followed by the chip erase command,
which in turn invokes the Embedded Erase algorithm. The device does not re-
quire the system to preprogram prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire memory for an all zero data
pattern prior to electrical erase. The system is not required to provide any con-
trols or timings during these operations. Table 30 on page 61 and Table 31 on
page 62 show the address and data requirements for the chip erase command
sequence.
When the Embedded Erase algorithm is complete, the device returns to the read
mode and addresses are no longer latched. The system can determine the status
of the erase operation by using DQ7, DQ6, or DQ2. Refer to Write Operation Sta-
tus on page 63 for information on these status bits.
Any commands written during the chip erase operation are ignored. However,
note that a hardware reset immediately terminates the erase operation. If this
Program Operation
or Write-to-Buffer
Sequence in Progress
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Autoselect and SecSi Sector
read operations are also allowed
Data cannot be read from erase- or
program-suspended sectors
Write Program Resume
Command Sequence
Read data as
required
Done
reading?
No
Yes
Write address/data
XXXh/30h
Device reverts to
operation prior to
Program Suspend
Write address/data
XXXh/B0h
Wait 15
μs
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL128N11FAIVH0 | 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 |
| S29GL128N11FFIVH2 | 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 |
| S29JL032J70TFI213 | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29PL032J65BFI150 | 2M X 16 FLASH 3V PROM, 65 ns, PBGA56 |
| S29PL127J70BFI000 | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL064A10FAIR10 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 8MX8/4MX16 100NS 64BGA - Trays |
| S29GL064A10FAIR50 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 100NS 64BGA - Trays |
| S29GL064A10FFIR30 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 8MX8/4MX16 100NS 64BGA - Trays |
| S29GL064A10TAIR42 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 8MX8/4MX16 100NS 48TSOP - Tape and Reel |
| S29GL064A10TAIR60 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 100NS 48TSOP - Trays |
發布緊急采購，3分鐘左右您將得到回復。