- 您現在的位置：買賣IC網 > PDF目錄374612 > S-4544A (Seiko Instruments Inc.) LCD Controller-Driver With Built-in 8-Bit and Serial Interfaces(內置8位和串行接口的LCD控制器-驅動器) PDF資料下載
參數資料
| 型號： | S-4544A |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | LCD Controller-Driver With Built-in 8-Bit and Serial Interfaces(內置8位和串行接口的LCD控制器-驅動器) |
| 中文描述： | LCD控制器與- 8內置驅動器位和串行接口（內置8位和串行接口的液晶顯示控制器-驅動器） |
| 文件頁數： | 11/39頁 |
| 文件大?。?/td> | 237K |
| 代理商： | S-4544A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
LCD Controller-Driver
S-4544A
10
Seiko Instruments Inc.
3.MPU Interface Select
In the S-4544A, the parallel interface or the serial interface can be selected.
Table 8 Interface Selection
P/SX Pin Logic
C86 Pin Logic
L
H
MPU Interface
80-family Interface
68-family Interface
H
L
don't care
Serial Interface
3.1 Parallel Interface
3.2 Serial Interface
P/SX
CSX
R/WX
A0
D0
D1
D2
D3 to D7
RDX
C86
By setting P/SX to “L.” the serial interface is selected. The instruction code is the same as for the parallel
interface. In this case, the RDX pin should be “Open.”
By setting CSX to “H,” the serial interface circuit is reset and the counter is initialized. By setting CSX to “L,” the
serial interface circuit enters an operating state.
The commands and displayed data are written at the rising edge of the serial clock. Data is input in the order D0 to
D7 in 8-bit data. The status and displayed data are read at the falling edge of the serial clock. Further displayed
data reading needs dummy reading.
: “L” Serial interface
: “L” Chip Active
: “L” WRITE Command
: “L” Command Data
: Serial Data Input
: Serial Clock Input
: Serial Data Output
: Open
: Open
: Open
“H” Parallel Interface
“H” Chip Reset
“H” READ Command
“H” Display Data
(SDI)
(SCLK)
(SDO)
When the serial interface is selected, the D2 pin (SDO: Serial Data Output Pin) goes
“
H
”
during reset.
Status reading in a reset operation is invalidated when the serial interface is selected. However,
“
H
”
is output to the
D2 pin (SDO: Serial Data Output Pin) . Serial clock wiring must be made by considering external noise and reflecting
noise. Be sure to check the operation of the equipment.
4. Command Execution Time
The command is completely executed within the cycle time (tcyc) according to the timing characteristics of the
command input. Therefore, commands can be input continuously without confirming the busy flag at the Status
Read mode. Reinputting the command within the cycle time is inhibited.
S-4544A Pin Name
A0
RDX
R/WX
CSX
D0 to D7
68-Family MPU Signal Name
A0
E
R/W
CS
D0 to D7
80-Family MPU Signal Name
A0
RD
WR
CS
D0 to D7
Table 9 Connection Relationship between MPU and Pins
A0
R/WX
Operation
L
H
L
H
L
H
H
L
Inputs the command
Reads the display data
Reads the status
Writes the display data
相關PDF資料 |
PDF描述 |
|---|---|
| S-4561A | LCD Controller-Driver With Built-in Serial and Parallel interfaces(內置串行和并行接口的LCD控制器-驅動器) |
| S-4562A | LCD CONTROLLER DRIVER |
| S-4601A | 64-bit THERMAL HEAD DRIVER |
| S-4602A | CMOS Thermal Print Head Driver Containing a 64-Bit Shift Register and a Latch(內置一個64位移位寄存器和一個鎖存器的CMOS 熱敏打印頭驅動器) |
| S-4610A | 64-bit THERMAL HEAD DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S4545 | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:T1/CEPT/ISDN-PRI TRANSFORMER |
| S455-003 | 制造商:Tripp Lite 功能描述:SCSI ULTRA2/U160/U320 LVD/SE CABLE - CHDC168(M) / HD68(M) - - Bulk |
| S455-006 | 功能描述:CABLE SCSI VHDCI68M/HD68M 6' RoHS:是 類別:電纜組件 >> 系列間適配器電纜 系列:- 標準包裝:1 系列:- 其它名稱:VS-M12MSD-RJ45-933-B/ 5,0VS-M12MSD-RJ45-933-B/5,0 |
| S455-010 | 功能描述:CABLE SCSI VHDCI68M/HD68M 10' RoHS:是 類別:電纜組件 >> 系列間適配器電纜 系列:- 標準包裝:1 系列:- 其它名稱:VS-M12MSD-RJ45-933-B/ 5,0VS-M12MSD-RJ45-933-B/5,0 |
| S4553 | 制造商:MERKLE-KORFF INDUSTRIES 功能描述:OLD COLMAN P/N: 2447901 |
發布緊急采購，3分鐘左右您將得到回復。