參數資料
型號: PXAC37KFA
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 16-bit microcontroller family(16位微控制器系列)
中文描述: 16-BIT, OTPROM, 32 MHz, MICROCONTROLLER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 19/68頁
文件大?。?/td> 344K
代理商: PXAC37KFA
Philips Semiconductors
Preliminary specification
XA-C3
XA 16-bit microcontroller family
32K/1024 OTP CAN transport layer controller
1 UART, 1 SPI Port, CAN 2.0B, 32 CAN ID filters, transport layer co-processor
2000 Jan 25
12
XA-C3 TIMER/COUNTERS
The XA has two standard 16–bit enhanced Timer/Counters: Timer 0
and Timer 1. Additionally, it has a third 16–bit Up/Down
timer/counter, T2. A central timing generator in the XA core provides
the time–base for all XA Timers and Counters. The timer/event
counters can perform the following functions:
– Measure time intervals and pulse duration
– Count External events
– Generate interrupt requests
– Generate PWM or timed output waveforms
All timer/counters (Timer 0, Timer 1 and Timer 2) can be
independently programmed to operate either as timers or event
counters. Timer 0 and Timer 1 are selectable via TMOD[6] and
TMOD[2], respectively. Timer 2 is selectable via T2CON[1]. All
timers may be dynamically read during program execution. All timers
count up unless otherwise stated.
When running in timer mode (as opposed to counter mode) the base
clock rate of all timers, including the Watchdog timer, is
user–programmable. The clock driving the timers is called TCLK
and is determined by the setting of two bits (PT1, PT0) (SCR[3:2]) in
the System Configuration Register – See Table 5. The frequency of
TCLK may be selected to be the oscillator input divided by 4 (fc/4),
the oscillator input divided by 16 (fc/16), or the oscillator input
divided by 64 (fc/64). This gives a range of possibilities for the XA
timer functions, including baud rate generation and Timer 2 capture.
Note: This single SCR rate setting applies to all timers.
When timers T0, T1, or T2 are used in the counter mode, the timers
will increment whenever a falling edge (high–to–low transition) is
detected on an External clock pin. These inputs are sampled once
every two oscillator cycles, so it can take as many as four oscillator
cycles to detect a transition. Thus, the maximum count rate that can
be supported is fc /4. In general, the duty cycle of the timer clock
inputs is not important. However, any high or low state on the timer
clock input pins must be present for two oscillator cycles before it is
guaranteed to be “seen” by the timer logic.
Timer 0 and Timer 1
These two Timer/Counters have four operating modes, which are
selected by bit–pairs (M1, M0) in the TMOD register. Timer modes
1, 2, and 3 in XA are kept identical to the 80C51 timer modes for
code compatibility. Only the mode 0 is replaced in the XA by a more
powerful 16–bit auto–reload mode. This gives the XA timers a much
larger range when used as time bases.
The recommended M1, M0 settings for the different modes are
shown in Figure 6.
PT1
PT0
CM
PZ
PT1
PT0
OPERATING
Prescaler selection.
Osc/4
Osc/16
Osc/64
Reserved
Compatibility Mode allows the XA to execute most translated 80C51 code on the XA. The
XA register file must copy the 80C51 mapping to data memory and mimic the 80C51 indirect
addressing scheme.
Page Zero mode forces all program and data addresses to 16-bits only. This saves stack space
and speeds up execution but limits memory access to 64k.
0
0
1
1
CM
0
1
0
1
PZ
SU00589
SCR Address:440
Not Bit Addressable
Reset Value: 00H
LSB
MSB
Figure 5. System Configuration Register (SCR)
GATE
C1 or
T1/
M1
M0
GATE
C0 or
T0/
M1
M0
LSB
MSB
GATE
Gating control when set. Timer/Counter “n” is enabled only while “INTn” pin is high and
“TRn” control bit is set. When cleared Timer “n” is enabled whenever “TRn” control bit is set.
Timer or Counter Selector cleared for Timer operation (input from internal system clock.)
Set for Counter operation (input from “Tn” input pin).
C/T
M1
0
0
1
1
M0
0
1
0
1
OPERATING
16-bit auto-reload timer/counter
16-bit non-auto-reload timer/counter
8-bit auto-reload timer/counter
Dual 8-bit timer mode (timer 0 only)
SU01325
TIMER 1
TIMER 0
TMOD Address:45C
Not Bit Addressable
Reset Value: 00H
Figure 6. Timer/Counter Mode Control (TMOD) Register
相關PDF資料
PDF描述
PXAG37 XA 16-bit microcontroller family(XA16位微控制器系列)
PXAG37KFBD XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
PXAG37KBA DIODE ZENER SINGLE 150mW 2Vz 5mA-Izt 0.045 150uA-Ir 1 SOD-523 3K/REEL
PXAG37KBBD XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
PXAG49 XA 16-bit microcontroller family(XA16位微控制器系列)
相關代理商/技術參數
參數描述
PXAC37KFA/00,512 功能描述:IC XA MCU 16BIT 32K OTP 44-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:XA 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
PXAC37KFBD 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family 32K/1024 OTP CAN transport layer controller 1 UART, 1 SPI Port, CAN 2.0B, 32 CAN ID Filters, transport layer co-proce
PXAC37KFBD/00,157 功能描述:8位微控制器 -MCU 16B MCU 32K/1024 1 UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PXAG30KBA 功能描述:16位微控制器 - MCU XA 16BIT 512R/2UART ROMLESS RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PXAG30KBA,512 功能描述:16位微控制器 - MCU XA 16BIT 512R/2UART RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT