- 您現在的位置：買賣IC網 > PDF目錄378058 > PMS430E325AFZ (Texas Instruments, Inc.) MIXED SIGNAL MICROCONTROLLER PDF資料下載
參數資料
| 型號： | PMS430E325AFZ |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | MIXED SIGNAL MICROCONTROLLER |
| 中文描述： | 混合信號微控制器 |
| 文件頁數： | 11/33頁 |
| 文件大?。?/td> | 437K |
| 代理商： | PMS430E325AFZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
MSP430C32x, MSP430P325A
MIXED SIGNAL MICROCONTROLLER
SLAS219B – MARCH 1999 – REVISED MARCH 2000
11
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
LCD drive
Liquid crystal displays (LCDs) for static, 2-, 3- and 4-MUX operations can be driven directly. The controller LCD
logic operation is defined by software using memory-bit manipulation. LCD memory is part of the LCD module,
not part of data memory. Eight mode and control bits define the operation and current consumption of the LCD
drive. The information for the individual digits can be easily obtained using table programming techniques
combined with the correct addressing mode. The segment information is stored in LCD memory using
instructions for memory manipulation.
The drive capability is mainly defined by the external resistor divider that supports the analog levels for 2-, 3-
and 4-MUX operation. Groups of the LCD segment lines can be selected for digital output signals. The
MSP430x32x configuration has four common signal lines and 21 segment lines.
A/D converter
The analog-to-digital converter (ADC) is a cascaded converter type that converts analog signals from V
CC
to
GND. It is a 12+2 bit converter with a software or automatically-controlled range select. Five inputs can be
selected for analog or digital function. A ratiometric current source can be used on four of the analog pins. The
current is adjusted by an external resistor and is enabled/disabled by bits located in the control registers. The
conversion is started by setting the start-of-conversion bit (SOC) in the control register and the
end-of-conversions sets the interrupt flag. The analog input signal is sampled starting with SOC during the next
twelve MCLK clock pulses. The power-down bit in the control register controls the operating mode of the ADC
peripheral. The current consumption and operation is stopped when it is set. The system reset PUC sets the
power-down bit.
Basic Timer1
The Basic Timer1 (BT1) divides the frequency of MCLK or ACLK, as selected with the SSEL bit, to provide low
frequency control signals. This is done within the system by one central divider, the Basic Timer1, to support
low current applications. The BTCTL control register contains the flags which controls or selects the different
operational functions. When the supply voltage is applied or when a reset of the device (RST/NMI pin), a
watchdog overflow, or a watchdog security key violation occurs, all bits in the register hold undefined or
unchanged status. The user software usually configures the operational conditions on the BT1 during
initialization.
The Basic Timer1 has two 8-bit timers which can be cascaded to a 16-bit timer. Both timers can be read and
written by software. Two bits in the SFR address range handle the system control interaction according to the
function implemented in the Basic Timer1. These two bits are the Basic Timer1 interrupt flag (BTIFG) and the
Basic Timer1 interrupt enable (BTIE) bit.
Watchdog Timer
The primary function of the Watchdog Timer (WDT) module is to perform a controlled system restart after a
software upset has occurred. If the selected time interval expires, a system reset is generated. If this watchdog
function is not needed in an application, the module can work as an interval timer, which generates an interrupt
after the selected time interval.
The Watchdog Timer counter (WDTCNT) is a 15/16-bit up-counter which is not directly accessible by software.
The WDTCNT is controlled using the Watchdog Timer control register (WDTCTL), which is an 8-bit read/write
register. Writing to WDTCTL, in both operating modes (watchdog or timer) is only possible by using the correct
password in the high-byte. The low-byte stores data written to the WDTCTL. The high-byte password is 05Ah.
If any value other than 05Ah is written to the high-byte of the WDTCTL, a system reset PUC is generated. When
the password is read it’s value is 069h This minimizes accidental write operations to the WDTCTL register. In
addition to the Watchdog Timer control bits, two bits included in the WDTCTL configure the NMI pin.
相關PDF資料 |
PDF描述 |
|---|---|
| PMS430E337AHFD | MIXED SIGNAL MICROCONTROLLERS |
| PN116 | Silicon planar type |
| PNA1605F | Silicon planar type |
| PN155 | Silicon NPN Phototransistor |
| PNZ155 | Silicon NPN Phototransistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PMS430E325FZ | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| PMS430E337 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Ultra-Low-Power Microcontroller. 32kB EPROM. 1KB RAM. USART. HW multiplier. 120 segment LCD |
| PMS430E337A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLERS |
| PMS430E337AHFD | 功能描述:16位微控制器 - MCU 16B Ultra-Low-Pwr Microcontroller RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| PMS430E337HFD | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。