![](http://datasheet.mmic.net.cn/260000/PIC17C42_datasheet_15942894/PIC17C42_180.png)
PIC17C4X
DS30412B-page 180
1996 Microchip Technology Inc.
Applicable Devices
42 R42 42A 43 R43 44
Output Low Voltage
I/O ports (except RA2 and RA3)
D080
D081
V
OL
with TTL buffer
–
–
–
–
–
–
0.1V
DD
0.1V
DD
*
0.4
V
V
V
I
OL
= V
DD
/1.250 mA
4.5V
≤
V
DD
≤
6.0V
V
DD
=
2.5V
I
OL
= 6 mA, V
DD
= 4.5V
Note 6
I
OL
= 60.0 mA, V
DD
= 6.0V
I
OL
= 1 mA, V
DD
= 4.5V
I
OL
= V
DD
/5 mA
(PIC17LC43/LC44 only)
D082
D083
D084
RA2 and RA3
OSC2/CLKOUT
(RC and EC osc modes)
–
–
–
–
–
–
3.0
0.4
V
V
V
0.1V
DD
*
Output High Voltage
(Note 3)
I/O ports (except RA2 and RA3)
D090
D091
V
OH
with TTL buffer
0.9V
DD
0.9V
DD
*
2.4
–
–
–
–
–
–
V
V
V
I
OH
= -V
DD
/2.500 mA
4.5V
≤
V
DD
≤
6.0V
V
DD
=
2.5V
I
OH
= -6.0 mA, V
DD
=4.5V
Note 6
Pulled-up to externally applied
voltage
I
OH
= -5 mA, V
DD
= 4.5V
I
OH
= -V
DD
/5 mA
(PIC17LC43/LC44 only)
D092
RA2 and RA3
–
–
12
V
D093
D094
OSC2/CLKOUT
(RC and EC osc modes)
2.4
0.9V
DD
*
–
–
–
–
V
V
Capacitive Loading Specs
on Output Pins
C
OSC2
OSC2/CLKOUT pin
D100
–
–
25
pF
In EC or RC osc modes when
OSC2 pin is outputting
CLKOUT.
external clock is used to drive
OSC1.
D101
C
IO
All I/O pins and OSC2
(in RC mode)
System Interface Bus
(PORTC, PORTD and PORTE)
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25
°
C unless otherwise stated. These parameters are for design guidance only and
are not tested.
These parameters are for design guidance only and are not tested, nor characterized.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC17CXX devices be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as coming out of the pin.
4: These specifications are for the programming of the on-chip program memory EPROM through the use of the
table write instructions. The complete programming specifications can be found in: PIC17CXX Programming
Specifications (Literature number DS30139).
5: The MCLR/V
PP
pin may be kept in this range at times other than programming, but is not recommended.
6: For TTL buffers, the better of the two specifications may be used.
–
–
50
pF
D102
C
AD
–
–
50
pF
In Microprocessor or
Extended Microcontroller mode
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40C
≤
T
A
≤
+85C for industrial and
0C
Operating voltage V
DD
range as described in Section 19.1
≤
T
A
≤
+70C for commercial
Parameter
No.
Sym
Characteristic
Min
Typ
Max
Units
Conditions
*