- 您現在的位置：買賣IC網 > PDF目錄368020 > PI7C7300ANA (Pericom Semiconductor Corp.) 3-PORT PCI-to-PCI BRIDGE PDF資料下載
參數資料
| 型號： | PI7C7300ANA |
| 廠商： | Pericom Semiconductor Corp. |
| 英文描述： | 3-PORT PCI-to-PCI BRIDGE |
| 中文描述： | 3端口PCI至PCI橋 |
| 文件頁數： | 62/109頁 |
| 文件大小： | 779K |
| 代理商： | PI7C7300ANA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
PI7C7300A
3-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 62 OF 109
09/25/03 Revision 1.09
signaled to the initiator, the initiator must relinquish the lock on the primary bus, and
therefore the lock is not yet established.
The first locked transaction must be a memory read transaction. Subsequent locked
transactions can be memory read or memory write transactions. Posted memory write
transactions that are a part of the locked transaction sequence are still posted. Memory
read transactions that are a part of the locked transaction sequence are not pre-fetched.
When the locked delayed memory read request is queued, PI7C7300A does not queue
any more transactions until the locked sequence is finished. PI7C7300A signals a target
retry to all transactions initiated subsequent to the locked read transaction that are
intended for targets on the other side of PI7C7300A. PI7C7300A allows any transactions
queued before the locked transaction to complete before initiating the locked transaction.
When the locked delayed memory read request transaction moves to the head of the
delayed transaction queue, PI7C7300A initiates the transaction as a locked read
transaction by de-asserting LOCK# on the target bus during the first address phase, and
by asserting LOCK# one cycle later. If LOCK# is already asserted (used by another
initiator), PI7C7300A waits to request access to the secondary bus until LOCK# is de-
asserted when the target bus is idle. Note that the existing lock on the target bus could
not have crossed PI7C7300A. Otherwise, the pending queued locked transaction would
not have been queued. When PI7C7300A is able to complete a data transfer with the
locked read transaction, the lock is established on the secondary bus.
When the initiator repeats the locked read transaction on the primary bus with the same
address, transaction type, and byte enable bits, PI7C7300A transfers the read data back to
the initiator, and the lock is then also established on the primary bus.
For PI7C7300A to recognize and respond to the initiator, the initiator’s subsequent
attempts of the read transaction must use the locked transaction sequence (de-assert
LOCK# during address phase, and assert LOCK# one cycle later). If the LOCK#
sequence is not used in subsequent attempts, a master timeout condition may result.
When a master timeout condition occurs, SERR# is conditionally asserted (see Section
7.4), the read data and queued read transaction are discarded, and the LOCK# signal is
de-asserted on the target bus.
Once the intended target has been locked, any subsequent locked transactions initiated on
the initiator bus that are forwarded by PI7C7300A are driven as locked transactions on
the target bus.
The first transaction to establish LOCK# must be Memory Read. If the first transaction is
not Memory read, the following transactions behave accordingly:
- Type 0 Configuration Read/Write induces master abort
- Type 1 Configuration Read/Write induces master abort
- I/O Read induces master abort
- I/O Write induces master abort
- Memory Write induces master abort
When PI7C7300A receives a target abort or a master abort in response to the delayed
locked read transaction, this status is passed back to the initiator, and no locks are
established on either the target or the initiator bus. PI7C7300A resumes forwarding
unlocked transactions in both directions.
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8140A | 2 PORT PCI TO PCI BRIDGE PLX PCI 6140 COMPARISON |
| PI7C8148B | 2-PORT PCI-to-PCI BRIDGE PLX PC16152 COMPARISON |
| PI7C8150B-33 | PCI Bridge | Asynchronous 2-Port PCI Bridge |
| PI7C8152B | PCI Bridge | Asynchronous 2-Port PCI Bridge |
| PI7C8154 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C7300ANAE | 功能描述:外圍驅動器與原件 - PCI 3 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C7300ANA-E | 制造商:Pericom Semiconductor Corporation 功能描述:PCI-to-PCI Bridge 272-Pin BGA 制造商:Pericom Semiconductor Corporation 功能描述:PCI to PCI Bridge 272-Pin BGA |
| PI7C7300DNAE | 功能描述:外圍驅動器與原件 - PCI PCI -to -PCI Bridge 3 Port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C7300EVB | 功能描述:界面開發工具 3 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C8140A | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2 PORT PCI TO PCI BRIDGE PLX PCI 6140 COMPARISON |
發布緊急采購，3分鐘左右您將得到回復。