參數資料
型號: PF48F4400P0VTQ0
廠商: INTEL CORP
元件分類: PROM
英文描述: OSC 5V SMT 7X5 CMOS
中文描述: 32M X 16 FLASH 1.8V PROM, 88 ns, PBGA88
封裝: 8 X 11 MM, 1.20 MM HEIGHT, LEAD FREE, SCSP-88
文件頁數: 64/102頁
文件大?。?/td> 1609K
代理商: PF48F4400P0VTQ0
1-Gbit P30 Family
April 2005
64
Intel StrataFlash
Embedded Memory (P30)
Order Number: 306666, Revision: 001
Datasheet
11.3.1
BEFP Requirements and Considerations
BEFP requirements:
Case temperature: T
C
= 25
°C
± 5
°C
V
CC
within specified operating range
VPP driven to V
PPH
Target block unlocked before issuing the BEFP Setup and Confirm commands
The first-word address (WA0) for the block to be programmed must be held constant from the
setup phase through all data streaming into the target block, until transition to the exit phase is
desired
WA0 must align with the start of an array buffer boundary
1
BEFP considerations:
For optimum performance, cycling must be limited below 100 erase cycles per block
2
BEFP programs one block at a time; all buffer data must fall within a single block
3
BEFP cannot be suspended
Programming to the flash memory array can occur only when the buffer is full
4
NOTES:
1.
Word buffer boundaries in the array are determined by A[4:0] (0x00 through 0x1F). The alignment start
point is A[4:0] = 0x00.
2.
Some degradation in performance may occur if this limit is exceeded, but the internal algorithm
continues to work properly.
3.
If the internal address counter increments beyond the block's maximum address, addressing wraps
around to the beginning of the block.
4.
If the number of words is less than 32, remaining locations must be filled with 0xFFFF.
11.3.2
BEFP Setup Phase
After receiving the BEFP Setup and Confirm command sequence, Status Register bit SR[7]
(Ready) is cleared, indicating that the WSM is busy with BEFP algorithm startup. A delay before
checking SR[7] is required to allow the WSM enough time to perform all of its setups and checks
(Block-Lock status, V
PP
level, etc.). If an error is detected, SR[4] is set and BEFP operation
terminates. If the block was found to be locked, SR[1] is also set. SR[3] is set if the error occurred
due to an incorrect V
PP
level.
Note:
Reading from the device after the BEFP Setup and Confirm command sequence outputs Status
Register data. Do not issue the Read Status Register command; it will be interpreted as data to be
loaded into the buffer.
11.3.3
BEFP Program/Verify Phase
After the BEFP Setup Phase has completed, the host programming system must check SR[7,0] to
determine the availability of the write buffer for data streaming. SR[7] cleared indicates the device
is busy and the BEFP program/verify phase is activated. SR[0] indicates the write buffer is
available.
相關PDF資料
PDF描述
PF48F4444PPVTQ0 Intel StrataFlash Embedded Memory
PF48F0P0VTQ0 Intel StrataFlash Embedded Memory
PF48F2P0VTQ0 Intel StrataFlash Embedded Memory
PF48F3P0VTQ0 Intel StrataFlash Embedded Memory
PF48F4P0VTQ0 Intel StrataFlash Embedded Memory
相關代理商/技術參數
參數描述
PF48F4400P0VTQ0A 制造商:Micron Technology Inc 功能描述:Flash Mem Parallel/Serial 1.8V 512M-Bit 32M x 16 88-Pin SCSP Tray 制造商:Micron Technology Inc 功能描述:NUMPF48F4400P0VTQ0A PF48F4400P0VTQ087456
PF48F4400P0Z0C0 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:StrataFlash? Cellular Memory
PF48F4400P0Z0Q0 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:StrataFlash? Cellular Memory
PF48F4400P0Z0W0 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:StrataFlash? Cellular Memory
PF48F4400P0Z3C0 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:StrataFlash?? Cellular Memory