- 您現在的位置：買賣IC網 > PDF目錄367729 > P8xC592 (NXP Semiconductors N.V.) 8-bit microcontroller with on-chip CAN PDF資料下載
參數資料
| 型號： | P8xC592 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit microcontroller with on-chip CAN |
| 中文描述： | 8位微控制器芯片的CAN |
| 文件頁數： | 69/108頁 |
| 文件大?。?/td> | 650K |
| 代理商： | P8XC592 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁當前第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
1996 Jun 27
69
Philips Semiconductors
Product specification
8-bit microcontroller with on-chip CAN
P8xC592
15.4
Power-down Mode
The instruction that sets bit PCON.1 to HIGH, is the last
one executed before entering the Power-down mode. In
Power-down mode the oscillator of the P8xC592 is
stopped. If the CAN-controller is in use, it is recommended
to set it into Sleep mode before entering Power-down
mode. However, setting PCON.1 to HIGH also sets the
Sleep bit (CAN-controller Command Register bit 4) to
HIGH.
The P8xC592 leaves Power-down mode either by a
hardware reset or by a CAN Wake-Up interrupt
(due to activity on the CAN-bus),
if the SIO1 (CAN) interrupt source is enabled
(contents of register IEN0 = 1X1XXXXXB).
A hardware reset affects the whole P8xC592, but leaves
the contents of the on-chip RAM unchanged
(CAN-controller-and CPU's SFRs are reset, see
Section 13.5.2, Chapter 17 and Table 40). A CAN
Wake-Up interrupt during Power-down mode causes a
reset output pulse with a width of 6144 machine cycles
(4.6 ms with f
CLK
= 16 MHz). All hardware except that for
the CAN-controller of the P8xC592 is reset (i.e. the
contents of all CAN-controller registers are preserved).
A capacitance connected to the RST pin can be used to
lengthen the internally generated reset pulse. If the pulse
exceeds 8192 machine cycles, the CAN-controller part is
reset too.
Table 82
Status of external pins during Idle and Power-down modes
Note
1.
If the port pins P1.6 and P1.7 are used as the CAN transmitter outputs (CTX0 and CTX1), then during Sleep and
Power-down mode these pins output a ‘recessive’ level (see Sections 13.5.2 and 13.5.11).
MODE
PROGRAM
ALE
PSEN
PORT0
PORT1
(1)
PORT2
PORT3
PORT4
PWM0/
PWM1
Idle
internal
external
internal
external
1
1
0
0
1
1
0
0
port data
floating
port data
floating
port data
port data
port data
port data
port data
address
port data
port data
port data
port data
port data
port data
port data
port data
port data
port data
1
1
1
1
Power-down
相關PDF資料 |
PDF描述 |
|---|---|
| P83C652EBAA | CMOS single-chip 8-bit microcontrollers |
| P83C652EHBB | CMOS single-chip 8-bit microcontrollers |
| P80C652EHBB | CMOS single-chip 8-bit microcontroller |
| P83C652FFP | CMOS single-chip 8-bit microcontrollers |
| P80C652FFP | CMOS single-chip 8-bit microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P8XCE598 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
| P8XCL580HFH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 8-bit microcontrollers with UART, I2C-bus and ADC |
| P8XCL580HFT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 8-bit microcontrollers with UART, I2C-bus and ADC |
| P8Z77 DELUXE | 制造商:Asus 功能描述:P8Z77-V Deluxe ATX Motherboard |
| P8Z77 M PRO | 制造商:Asus 功能描述:P8Z77-M Pro MicroATX Motherboard |
發布緊急采購，3分鐘左右您將得到回復。