參數資料
型號： NSB8
廠商： Electronic Theatre Controls, Inc.
英文描述： BASIC interpreter for Z80 family
中文描述： Z80的BASIC解釋為家庭
文件頁數： 71/158頁
文件大?。?/td> 752K
代理商： NSB8
ITALIAN TECHNOLOGY
grifo
Page 59
NSB8 Rel. 5.10
CONTROL-C
, THE PANIC BUTTON
Occasionally, you may desire to interrupt a program’s execution at some random point while it is
running. This may be because you wish to repair a program error, or because you do not want program
execution to continue to completion.
Your panic button is <control-C>. This stop everything signal is sent to the card whenever you hold
down the control key then press the C key at the same time on your PC.
If a program is running, the currently executing statement will finish, and the message
STOP IN LINE XXXXX
will be printed on the terminal, where XXXXX will actually be the line number where execution
stopped.
If you are listing a program when <control-C> is pushed, the line being listed will completed, and
the message
STOP
will be sent to the console terminal.
Whenever you use <control-C>, you will be returned to BASIC’s direct mode, where you are free
to examine the program and variables.
Perhaps you may someday panic out of a long running program because you fear that is caught in
an endless loop. However, upon examination of the program and its variables, you discover that the
program is operating correctly, but just takes a long time to finish. In this and similar instances, you
may use the CONT command to resume execution at the point where the program was interrupted
by <control-C>. You may not use CONT if, during the interruption, you modify any part of the
program text.
BASIC may be instructed to ignore the <control-C> command. This is accomplished by changing
certaine internal data in the BASIC interpreter itself, a procedure described in section
PERSONALIZING BASIC. Because it involves modification to BASIC and also makes it impossible
to stop an improperly written runaway program without somehow stopping the computer altogether,
you should leave <control-C> enabled until you program is fully debugged.
SEE ALSO:
Command CONT
Statement STOP
Section SOME BASIC CONCEPTS
Section PERSONALIZING BASIC
相關PDF資料
PDF描述
NSB9435T1 High Current Bias Resistor Transistors(高強度電流偏置電阻晶體管)
NSBA114EDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBA114YDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBC143TPDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBC144EPDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
相關代理商/技術參數
參數描述
NSB8AT 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Glass Passivated General Purpose Plastic Rectifier
NSB8AT/31 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
NSB8AT/45 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
NSB8AT/81 功能描述:二極管 - 通用，功率，開關 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube
NSB8AT-E3/31 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*