參數資料
型號: NSB8
廠商: Electronic Theatre Controls, Inc.
英文描述: BASIC interpreter for Z80 family
中文描述: Z80的BASIC解釋為家庭
文件頁數: 128/158頁
文件大小: 752K
代理商: NSB8
grifo
ITALIAN TECHNOLOGY
Page 116
NSB8 Rel. 5.10
PERSONALIZING BASIC
You may change certain of BASIC’s internal features so that system operation is more convenient
for you and/or better fits your particular computer’s capabilities. For example, the limits of the
memory area used by BASIC may be enlarged or constricted, leaving more or less space for user
programs and data. These changes are accomplished through the modification of information stored
in various memory locations within the BASIC interpreter itself.
In general, modifications of these personalization bytes are best handled through use of BASIC’s
FILL statement, and, occasionally, the built in EXAM function. What follows is a complete, step by
step procedure which you may use to personalize BASIC in your computer system. If you want the
changes made to be permanent, be sure to follow all of the steps (from A to E). If you want only
temporary modification, which will endure until the end of the current session of BASIC, then do
only step C, omitting all the rest.
A)
Test your system’s memory by using an operating system memory test function to be sure that
you will not be making a copy of BASIC from bad memory. In particular, the area where
BASIC and
GDOS 80
reside should be tested thoroughly.
B)
At this point, you should make sure that the
GDOS 80
is operational, and that you are in its
command mode (signified by the
GDOS 80
prompt). Now, run the original
NSB8
saved in the
received disk, by typing:
NSB8
<CR>
When BASIC responds with READY, go to step C.
C)
Now you are ready to make the various modifications to BASIC. In order to do so, follow the
substeps of the following paragraphs in exactly the order given. If you do not wish to make one
or more of the individual changes listed, then simply skip it, but don't mix up the order of the
steps! In any case, you must always do step 2 before attempting any higher numbered steps.
D)
Type BYE in order to return to the
GDOS 80
and save the modified version of BASIC to a new
file on one of the managed drives. This operation is performed through the following
GDOS
command:
SAVE <size of BASIC file in 256 bytes blocks> <drive:filename>
<CR>
With the standard version, then the above simplifies to the following actual command:
SAVE 43 C:NSB8MOD.G80
<CR>
E)
Now type:
C:NSB8MOD
<CR>
to test your personalized copy and make sure that all the modifications have been made
correctly. If not, get back into
GDOS 80
and return to step A. The new copy of BASIC may
now be used as your personalized master copy, and it is a good practise to make a back up copy
for example on write protect disk.
相關PDF資料
PDF描述
NSB9435T1 High Current Bias Resistor Transistors(高強度電流偏置電阻晶體管)
NSBA114EDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBA114YDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBC143TPDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBC144EPDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
相關代理商/技術參數
參數描述
NSB8AT 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Glass Passivated General Purpose Plastic Rectifier
NSB8AT/31 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
NSB8AT/45 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
NSB8AT/81 功能描述:二極管 - 通用,功率,開關 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube
NSB8AT-E3/31 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel