參數資料
型號： NSB8
廠商： Electronic Theatre Controls, Inc.
英文描述： BASIC interpreter for Z80 family
中文描述： Z80的BASIC解釋為家庭
文件頁數： 141/158頁
文件大小： 752K
代理商： NSB8
ITALIAN TECHNOLOGY
grifo
Page A-1
NSB8 Rel. 5.10
APPENDIX A: COMMAND FILE FOR GDOS 80
If you need to create a command file (a directly executable program) for the
GDOS 80
operating
system, starting from a source program written for
NSB8
, the following steps must be performed.
This methods is similar to the personalization process above described, and you can configure a copy
of BASIC so that a BASIC program begins automatically as soon as BASIC itself is up and
running. This is especially desirable when you want to create an automatic software system intended
for use by persons who are unfamiliar with BASIC or
GDOS
operation, or in embedded systems.
a
) The
NSB8
program must be created and completely tested in all its parts ensuring that any syntax
and logical errors are eliminated. In other words you must obtain the final version of your program.
b
) Inside
NSB8
environment, with the tested program already loaded, type the command:
PSIZE<CR>
that shows the program length in blocks of 256 bytes. Call SIZE_APPL the shown value and use
it in the following steps.
c
) Execute the following commands by directly using the BASIC on line interpreter:
FILL 3599,00
<CR>
FILL 256,195
<CR>
FILL 257,00
<CR>
FILL 258,14
<CR>
This commands set the autostart flag (address 3599 = E0FH) and put a jump to
NSB8
default entry
point (address E00H) at the beginning of
GDOS 80
command file.
d
) Type BYE in order to return to the
GDOS 80
, indicated by the proper prompt
ABACO(r)>
representation.
e
) Type the
GDOS
direct comand:
SAVE nn <drive:filename.G80>
<CR>
where
nn
correspond to the result of the sum
67+SIZE_APPL
in
hexadecimal
.
At this point, when the operating system prompt is redisplayed, the command file has been created
and it is the file
filename.G80
created on the specified
drive
. This file can be directly tested thanks
to operating system capability to load and execute a command file:
<drive:filename>
<CR>
For example to create a
GDOS 80
autorun program on target card RAM disk, with a BASIC
program length SIZE_APPL=3, the command:
SAVE 46 M:AUTORUN.G80
<CR>
must be typed. At the following reset or power on the card will automatically execute the program.
相關PDF資料
PDF描述
NSB9435T1 High Current Bias Resistor Transistors(高強度電流偏置電阻晶體管)
NSBA114EDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBA114YDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBC143TPDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
NSBC144EPDXV6T1 Dual Bias Resistor Transistors(雙偏置電阻晶體管)
相關代理商/技術參數
參數描述
NSB8AT 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Glass Passivated General Purpose Plastic Rectifier
NSB8AT/31 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
NSB8AT/45 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
NSB8AT/81 功能描述:二極管 - 通用，功率，開關 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube
NSB8AT-E3/31 功能描述:整流器 50 Volt 8.0 Amp 125 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*