- 您現在的位置：買賣IC網 > PDF目錄69040 > MSM9225BGA-2K (OKI ELECTRIC INDUSTRY CO LTD) 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MSM9225BGA-2K |
| 廠商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PQFP44 |
| 封裝： | PLASTIC, QFP-44 |
| 文件頁數： | 43/95頁 |
| 文件大?。?/td> | 567K |
| 代理商： | MSM9225BGA-2K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
MSM9225B User’s Manual
Chapter 2 Register Descriptions
2 – 35
2.4.9 Standby Control Register (STBY: 8Ehex)
This register is used for setting the stop mode and the sleep mode.
A “0” is read after the stop or sleep mode is terminated.
The bit configuration is as follows:
MSB
Not
used
Not
used
Not
used
Not
used
Not
used
Not
used
SLEEP STOP
LSB
STBY (8Ehex), R/W: R/W
Initial
value:
00
0
Normal operation
1
Set stop mode
0
Normal operation
1
Set sleep mode
Unused bit.
Write a “0”.
Note:
A “0” is read out after the sleep mode or the stop mode is terminated.
Figure 2-33 Standby Control Register (STBY)
(1) Stop mode: STOP
If STOP is set to “1”, the MSM9225B will enter the stop mode when the CAN bus is idle.
In stop mode, the contents of the message memory and control registers are held but the oscillator and all
circuits stop to save power consumption. Access to/from external units is therefore disabled.
Stop mode is terminated by a reset signal input from the
RESET pin or a “L” level input to the CS pin.
At reset, STOP is set to “0”.
(2) Sleep mode: SLEEP
If SLEEP is set to “1”, the MSM9225B will enter the sleep mode when the CAN bus is idle.
In sleep mode, the contents of the message memory and control registers are held and the differential input
of Rx0 and Rx1 operates, but the oscillator and other circuits stop operation. Access to/from external units
is therefore disabled.
Sleep mode is terminated by a reset signal input from the
RESET pin or a “L” level input to the CS pin, or
by the differential input of Rx0 and Rx1.
When both stop mode and sleep mode are set at the same time, the MSM9225B enters stop mode.
At reset, SLEEP is set to “0”.
相關PDF資料 |
PDF描述 |
|---|---|
| MSP430A003IPW | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| MSP430A004IPWR | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| MSP430A005IPWR | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO28 |
| MSP430A004IPW | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| MSP430A019IRHBR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM9225BGAZ020 | 制造商:ROHM Semiconductor 功能描述: |
| MSM9225BGAZ0VL | 制造商:ROHM Semiconductor 功能描述: |
| MSM9405 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:IrDA Communication Controller |
| MSM9552 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LSI for FM Multiplex Data Demodulation |
| MSM9552GS-2K | 制造商:ROHM Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。