參數資料
型號： MM908E621ACDWB
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Integrated Quad Half-Bridge and Triple High-Side with Embedded MCU and LIN for High End Mirror
中文描述： 綜合四半橋和三高的嵌入式微控制器和LIN高端側鏡
文件頁數： 25/62頁
文件大?。?/td> 540K
代理商： MM908E621ACDWB
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
908E621
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Stop mode has a higher current consumption than Sleep
mode, but allows a quicker wake-up. Additionally the wake-
up sources can be selected (maskable) which is not possible
in Sleep mode.
Figure 12
show the procedure to enter the Stop mode and
how the system is waking up.
Figure 12. STOP mode Wake-up Procedure
Sleep Mode
In Sleep mode the voltage regulator is turned off and the
MCU is not supplied (V
DD
= 0 V) also the
RST_A
terminal is
pulled low.
To enter the Sleep mode the Sleep bit in the System
Control Register has to be set.
Wake-up from this mode is possible by LIN bus activity or
the wake-up input L0 and is not maskable. The wake-up
behaves like a power on reset. The wake-up / reset source
can be evaluated by the L0WF and/or LINWF bits in the
Reset Status Register.
Sleep mode has a lower current consumption than Stop
mode, but requires a longer time to wake-up. The wake-up
sources can not be selected (not maskable).
Figure 13
show the procedure to enter the Sleep mode
and how a wake-up is performed.
Figure 13. SLEEP mode Wake-up Procedure
Table 6
summarized the Operating modes.
From Reset
initialize
operate
SPI:
STOP =1
MCU STOP
IRQ
interrupt
SPI: reason for
interrupt
Switch to VREG
low current mode
Assert IRQ
Switch to VREG
high current mode
MCU
Power Die
Wake Up on
LIN or L0
Enable/disable
LIN/L0 wakeup
From Reset
initialize
operate
SPI:
SLEEP =1
Switch off VREG
Vdd low, RST low
Store Wake Up
Event
Start VREG
Vdd high, RST
high
MCU
Power Die
Wake Up on
LIN or L0
相關PDF資料
PDF描述
MM908E624 Integrated Triple High-Side Switch with Embedded MCU and LIN Serial Communication for Relay Drivers(集成三高端開關，帶嵌入式MCU和LIN串行通信功能，用于繼電器驅動器)
MM908E625ACDWB Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
MM908E625 Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication(集成四半H橋，帶電源、嵌入式MCU和LIN串行通信功能)
MM908E626AVDWB Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626R2 Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
相關代理商/技術參數
參數描述
MM908E621ACDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-bridge and Triple High Side with Embedded MCU and LIN for High End Mirror
MM908E621ACDWBR2 功能描述:8位微控制器 -MCU QUAD HB / TRIPLE HS 841B RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E621ACPEK 功能描述:8位微控制器 -MCU QUAD H-B/3-HS W/MCU & LI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E621ACPEKR2 功能描述:8位微控制器 -MCU QUAD HB AND TRIPLE HS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E622 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-Bridge, Triple High-Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*