參數資料
型號： MCHC705P6ACSDR2
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER
文件頁數： 74/130頁
文件大小： 1541K
代理商： MCHC705P6ACSDR2
Interrupts
Advance Information
MC68HC705P6A — Rev. 2.0
48
Interrupts
MOTOROLA
5.3.1 Reset Interrupt Sequence
The reset function is not in the strictest sense an interrupt; however, it is
acted upon in a similar manner as shown in Figure 5-1. A low-level input
on the RESET pin or internally generated RST signal causes the
program to vector to its starting address which is specified by the
contents of memory locations $1FFE and $1FFF. The I bit in the
condition code register is also set. The MCU is configured to a known
state during this type of reset as previously described in Section 4.
Resets.
5.3.2 Software Interrupt (SWI)
The SWI is an executable instruction. It is also a non-maskable interrupt
since it is executed regardless of the state of the I bit in the CCR. As with
any instruction, interrupts pending during the previous instruction will be
serviced before the SWI opcode is fetched. The interrupt service routine
address for the SWI instruction is specified by the contents of memory
locations $1FFC and $1FFD.
5.3.3 Hardware Interrupts
All hardware interrupts are maskable by the I bit in the CCR. If the I bit is
set, all hardware interrupts (internal and external) are disabled. Clearing
the I bit enables the hardware interrupts. Four hardware interrupts are
explained in the following subsections.
5.3.3.1 External Interrupt (IRQ)
The IRQ/VPP pin drives an asynchronous interrupt to the CPU. An edge
detector flip-flop is latched on the falling edge of IRQ/VPP. If either the
output from the internal edge detector flip-flop or the level on the
IRQ/VPP pin is low, a request is synchronized to the CPU to generate the
IRQ interrupt. If the LEVEL bit in the mask option register is clear (edge-
sensitive only), the output of the internal edge detector flip-flop is
sampled and the input level on the IRQ/VPP pin is ignored. The interrupt
service routine address is specified by the contents of memory locations
相關PDF資料
PDF描述
MC68HC705P6AMP 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28
MC68HC705P6CDW 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
MC68HC705P6P 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28
MC68HC705P6DW 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
MC68HC705P6S 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, CDIP28
相關代理商/技術參數
參數描述
MCHC711KS2CFNE3 功能描述:8位微控制器 -MCU 32K EPROM - SLO MODE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MCHC711KS2CFNE4 功能描述:8位微控制器 -MCU 32K EPROM - SLO MODE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MCHC711KS2MFNE4 功能描述:IC MCU 3MHZ 32K EPROM 68-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:1 系列:87C 核心處理器:MCS 51 芯體尺寸:8-位 速度:16MHz 連通性:SIO 外圍設備:- 輸入/輸出數:32 程序存儲器容量:8KB（8K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 6 V 數據轉換器:- 振蕩器型:外部 工作溫度:0°C ~ 70°C 封裝/外殼:44-DIP 包裝:管件 其它名稱:864285
MCHC711KS2VFNE3 功能描述:8位微控制器 -MCU 32K EPROM - SLO MODE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MCHC812A4CPV5 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*