- 您現在的位置：買賣IC網 > PDF目錄69028 > MC68HC16S2CPU25 (FREESCALE SEMICONDUCTOR INC) 16-BIT, 25.17 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MC68HC16S2CPU25 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, 25.17 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 41/104頁 |
| 文件大?。?/td> | 812K |
| 代理商： | MC68HC16S2CPU25 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
MC68HC16S2
MOTOROLA
MC68HC16S2TS/D
41
When an external device asserts RESET for the proper period, reset control logic clocks the signal into
an internal latch. The control logic drives the RESET pin low for an additional 512 CLKOUT cycles after
it detects that the RESET signal is no longer being externally driven, to guarantee this length of reset
to the entire system.
If an internal source asserts the reset signal, the reset control logic asserts RESET for a minimum of
512 cycles. If the reset signal is still asserted at the end of 512 cycles, the control logic continues to
assert RESET until the internal reset signal is negated.
After 512 cycles have elapsed, the RESET pin goes to an inactive, high-impedance state for ten cycles.
At the end of this 10-cycle period, the RESET pin is tested. When the input is at logic level one, reset
exception processing begins. If, however, the RESET pin is at logic level zero, the reset control logic
drives the pin low for another 512 cycles. At the end of this period, the pin again goes to high-impedance
state for ten cycles, then it is tested again. The process repeats until RESET is released.
3.8.4 Power-On Reset
When the SIM clock synthesizer is used to generate the system clock, power-on reset involves special
circumstances related to application of system and clock synthesizer power. Regardless of clock
source, voltage must be applied to clock synthesizer power input pin VDDSYN in order for the MCU to
operate. The following discussion assumes that VDDSYN is applied before and during reset. This mini-
mizes crystal start-up time. When VDDSYN is applied at power-on, start-up time is affected by specific
crystal parameters and by oscillator circuit design. VDD ramp-up time also affects pin state during reset.
During power-on reset, an internal circuit in the SIM drives the IMB and external reset lines. The circuit
releases the internal reset line as VDD ramps up to the minimum specified value, and SIM pins are ini-
tialized. As VDD reaches a specified minimum value, the clock synthesizer VCO begins operation and
clock frequency ramps up to specified limp mode frequency. The external RESET line remains asserted
until the clock synthesizer PLL locks and 512 CLKOUT cycles elapse.
The SIM clock synthesizer provides clock signals to the other MCU modules. After the clock is running
and the internal reset signal is asserted for four clock cycles, these modules reset. VDD ramp time and
VCO frequency ramp time determine how long these four cycles take. Worst case is approximately 15
milliseconds. During this period, module port pins may be in an indeterminate state. While input-only
pins can be put in a known state by means of external pull-up resistors, external logic on input/output
or output-only pins must condition the lines during this time. Active drivers require high-impedance buff-
ers or isolation resistors to prevent conflict.
3.8.5 Use of Three-State Control Pin
Asserting the three-state control (TSC) input causes the MCU to put all output drivers in an inactive,
change state. There are certain constraints on use of TSC during power-on reset:
When the internal clock synthesizer is used (MODCLK held high during reset), synthesizer ramp-
up time affects how long the ten cycles take. Worst case is approximately 20 ms from TSC asser-
tion.
When an external clock signal is applied (MODCLK held low during reset), pins go to high-imped-
ance state as soon after TSC assertion as ten clock pulses have been applied to the EXTAL pin.
When TSC assertion takes effect, internal signals are forced to values that can cause inadvertent
mode selection. Once the output drivers change state, the MCU must be powered down and re-
started before normal operation can resume.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC16S2CPU20B1 | 16-BIT, 20.97 MHz, MICROCONTROLLER, PQFP100 |
| MC68HC16X1CTH | 16-BIT, MROM, 16.78 MHz, MICROCONTROLLER, PQFP120 |
| MC68HC24VP | 16 I/O, PIA-GENERAL PURPOSE, PDIP40 |
| MC68HC33CFG | 48 I/O, PIA-GENERAL PURPOSE, PQFP100 |
| MC68HC33FG | 48 I/O, PIA-GENERAL PURPOSE, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC16Z1CAG | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC16Z1CAG16 | 功能描述:16位微控制器 - MCU 16 BIT MCU 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MC68HC16Z1CAG16 | 制造商:Freescale Semiconductor 功能描述:IC16-BIT MICROCONTROLLER |
| MC68HC16Z1CAG20 | 功能描述:16位微控制器 - MCU 16 BIT MCU 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MC68HC16Z1CAG20 | 制造商:Freescale Semiconductor 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。