- 您現在的位置：買賣IC網 > PDF目錄67966 > MC68HC05F8B (MOTOROLA INC) 8-BIT, MROM, MICROCONTROLLER, PDIP56 PDF資料下載
參數資料
| 型號： | MC68HC05F8B |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, MICROCONTROLLER, PDIP56 |
| 封裝： | SDIP-56 |
| 文件頁數： | 4/126頁 |
| 文件大?。?/td> | 736K |
| 代理商： | MC68HC05F8B |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
MC68HC05F8
MOTOROLA
11-1
LOW POWER MODES
11
LOW POWER MODES
The STOP and WAIT instructions have different effects on the Timers, Serial Peripheral Interface
(SPI), and DTMF/Melody Generator (DMG). These are discussed in the following paragraphs.
11.1
Stop Mode
When the processor executes the STOP instruction, the internal clock is turned off. This halts all
internal CPU processing, including the operation of the Programmable Timer, SPI and DMG. The
I bit in the Condition Code register is cleared to enable external interrupts (INTE1, INTE2 and
KEYE bits are unaltered). All registers and memory remain unaltered, and all input/output lines
remain unchanged.
The MCU is exited from Stop mode by an interrupt on either IRQ1 or IRQ2, or any keyboard
interrupts, or any resets (logic low on RESET pin or a power-on reset). On exit from Stop mode,
the program counter is loaded with the corresponding interrupt vector (see Table 5-1). The effects
of the Stop mode on each of the MCU peripheral systems are described separately.
11.1.1
Timer A during Stop Mode
When Stop mode is entered, the timer A (programmable timer) counter stops counting (the
internal processor clock is stopped) and remains at that particular count value until the Stop mode
is exited. If the exit was caused by reset, the counter is forced to $FFFC. If the Stop mode is exited
by an interrupt (IRQ1, IRQ2, or keyboard interrupt), the counter resumes counting from the value
when it entered the Stop mode. Another feature of the programmable timer in the Stop mode is,
that if at least one valid input capture edge occurs at the TCAP pin, the input capture detect
circuitry is armed. This action does not set any timer ags or “wake up” the MCU, but when the
MCU does “wake up” there will be an active input capture ag (and data) from that rst valid edge
which occurred during the Stop mode. Notice that an exit by a reset will reset the entire MCU and
thus, this function on the TCAP will not happen.
TPG
99
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC705F8FU | 8-BIT, OTPROM, 1.8 MHz, MICROCONTROLLER, PQFP64 |
| MC68HC05L16CFU | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC705L16CFU | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC05L16FU | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC05P18AP | 8-BIT, MROM, MICROCONTROLLER, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05J1 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05J1A | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ACDW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ACP | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ADW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。
