參數資料
型號： MBM29LV004T
廠商： Fujitsu Limited
英文描述： CMOS 4M (512K ×8) Bit Flash Memory( 單5V 電源電壓512K ×8位閃速存儲器)
中文描述： 的CMOS 4分（為512k × 8）位快閃記憶體（單5V的電源電壓為512k × 8位閃速存儲器）
文件頁數： 17/47頁
文件大小： 358K
代理商： MBM29LV004T
17
MBM29LV004T/MBM29LV004B
Write Operation Status
Notes:
1. Performing successive read operations from the erase-suspended sector will cause DQ
2
to toggle.
2. Performing successive read operations from any address will cause DQ
6
to toggle.
3. Reading the byte address being programmed while in the erase-suspend program mode will indicate
logic “1” at the DQ
2
bit. However, successive reads from the erase-suspended sector will cause DQ
2
to
toggle.
4. DQ
0
and DQ
1
are reserve pins for future use.
5. DQ
4
is for Fujitsu internal use only.
DQ
7
Data Polling
The MBM29LV004T/004B devices feature Data Polling as a method to indicate to the host that the Embedded
Algorithms are in progress or completed. During the Embedded Program Algorithm an attempt to read the device
will produce the complement of the data last written to DQ
7
. Upon completion of the Embedded Program
Algorithm, an attempt to read the device will produce the true data last written to DQ
7
. During the Embedded
Erase Algorithm, an attempt to read the device will produce a “0” at the DQ
7
output. Upon completion of the
Embedded Erase Algorithm an attempt to read the device will produce a “1” at the DQ
7
output. The flowchart
for Polling (DQ
7
) is shown in Figure 16.
For chip erase and sector erase, the Data Polling is valid after the rising edge of the sixth WE pulse in the six
write pulse sequence. Data Polling must be performed at sector address within any of the sectors being erased
and not a protected sector. Otherwise, the status may not be valid. Once the Embedded Algorithm operation is
close to being completed, the MBM29LV004T/004B data pins (DQ
7
) may change asynchronously while the
output enable (OE) is asserted low. This means that the device is driving status information on DQ
7
at one instant
of time and then that byte's valid data at the next instant of time. Depending on when the system samples the
DQ
7
output, it may read the status or valid data. Even if the device has completed the Embedded Algorithm
operation and DQ
7
has a valid data, the data outputs on DQ
0
to DQ
6
may be still invalid. The valid data on DQ
0
to DQ
7
will be read on the successive read attempts.
The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase
Algorithm, or sector erase time-out. (See Table 7.)
See Figure 10 for the Data Polling timing specifications and diagrams.
Table 7 Hardware Sequence Flags
Status
DQ
7
DQ
6
DQ
5
DQ
3
DQ
2
In Progrress
Embedded Program Algorithm
Toggle
0
0
1
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
Erase
Suspended
Mode
Erase Suspend Read
(Erase Suspended Sector)
1
1
0
0
Toggle
(Note 1)
Erase Suspend Read
(Non-Erase Suspended Sector)
Data
Data
Data
Data
Data
Erase Suspend Program (Non-
Erase Suspended Sector)
Toggle
(Note 2)
0
0
1
(Note 3)
Exceeded
Time Limits
Embedded Program Algorithm
Toggle
1
0
1
Program/Erase in Embedded Erase Algorithm
0
Toggle
1
1
N/A
Erase
Suspended
Mode
Erase Suspend Program
(Non-Erase Suspended Sector)
Toggle
1
0
N/A
DQ
7
DQ
7
DQ
7
DQ
7
相關PDF資料
PDF描述
MBM29LV004 CMOS 4M SON Packages Flash Memory(CMOS 4M小外形封裝閃速存儲器)
MBM29LV080 CMOS 8M SON Packages Flash Memory(CMOS 8M小外形封裝閃存)
MBM29LV400 CMOS 4M SON Packages Flash Memory(CMOS 4M小外形封裝閃存)
MBM29LV800 CMOS 8M SON Packages Flash Memory(CMOS 8M小外形封裝閃存)
MBM29LV002 CMOS 2 M SON Packages Flash Memory(CMOS 2M 小外形封裝閃速存儲器)
相關代理商/技術參數
參數描述
MBM29LV004T-12PNS-X-EE 制造商:FUJITSU 功能描述:
MBM29LV004T12PNSXR 制造商:FUJITSU 功能描述:
MBM29LV004TC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004TC-12 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004TC-12PNS 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*