參數資料
型號： MB90V330A
廠商： Fujitsu Limited
英文描述： 16-bit Proprietary Microcontroller
中文描述： 16位微控制器專有
文件頁數： 15/116頁
文件大?。?/td> 632K
代理商： MB90V330A
MB90330 Series
15
■
HANDLING DEVICES
1.
Preventing latchup and turning on power supply
Latchup may occur on CMOS IC under the following conditions:
If a voltage higher than V
CC
or lower than V
SS
is applied to input and output pins.
A voltage higher than the rated voltage is applied between V
CC
and V
SS
.
If the AV
CC
power supply is turned on before the V
CC
voltage.
Ensure that you apply a voltage to the analog power supply at the same time as V
CC
or after you turn on the
digital power supply (when you perform power-off, turn off the analog power supply first or at the same time as
V
CC
and the digital power supply).
If latch-up occurs, the supply current increases rapidly, sometimes resulting in thermal breakdown of the device.
Use meticulous care not to let any voltage exceed the maximum rating.
Treatment of unused pins
2.
Leaving unused input pins unconnected can cause abnormal operation or latchup, leading to permanent damage.
Unused input pins should always be pulled up or down through resistance of at least 2 k
. Any unused input/
output pins may be set to output mode and left open, or set to input mode and treated the same as unused input
pins. If there is unused output pin, make it to open.
Treatment of power supply pins on models with A/D converters
Even when the A/D converters are not in use, be sure to make the necessary connections AV
CC
=
AVRH
=
V
CC
,
and AV
SS
=
V
SS
.
About the attention when the external clock is used
Using external clock
3.
4.
5.
Treatment of power supply pins (V
CC
/V
SS
)
In products with multiple V
CC
or V
SS
pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the V
CC
and V
SS
pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
μ
F between V
CC
and V
SS
near
this device.
About Crystal oscillator circuit
6.
Noise near the X0/X1 pins and X0A/X1A pins may cause the device to malfunction. Design the printed circuit
board so that X0/X1 pins and X0A/X1A pins, the crystal oscillator (or the ceramic oscillator) and the bypass
capacitor to ground are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0/X1 pins and X0A/X1A pins surrounded
by ground plane because stable operation can be expected with such a layout.
X0
X1
OPEN
相關PDF資料
PDF描述
MB90F342CE 16-bit Proprietary Microcontroller CMOS
MB90F345CESPF 16-bit Proprietary Microcontroller CMOS
MB90F345CESPFV 16-bit Proprietary Microcontroller CMOS
MB90F345E 16-bit Proprietary Microcontroller CMOS
MB90F345EPF 16-bit Proprietary Microcontroller CMOS
相關代理商/技術參數
參數描述
MB90V340A-102CR 制造商:FUJITSU 功能描述:
MB-910 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS
MB9100100 制造商:COM/DUO 功能描述:FAN 4-6WKS
MB9100-100 制造商:COM/DUO 功能描述:FAN 4-6WKS
MB91101 制造商:Panasonic Industrial Company 功能描述:IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*