- 您現在的位置：買賣IC網 > PDF目錄377922 > MB90F244 (Fujitsu Limited) Octal Edge-Triggered D-type Flip-Flops With Clock Enable 20-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90F244 |
| 廠商： | Fujitsu Limited |
| 英文描述： | Octal Edge-Triggered D-type Flip-Flops With Clock Enable 20-CFP -55 to 125 |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 15/67頁 |
| 文件大?。?/td> | 1403K |
| 代理商： | MB90F244 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
15
MB90F244
5. Crystal Oscillation Circuit
Noise in the vicinity of the X0 and X1 pins will cause this device to operate incorrectly. Design the printed circuit
board so that the bypass capacitor connecting X0 and X1 pins and the crystal oscillator (or ceramic oscillator)
to ground is located as close to the device as possible.
In addition, because printed circuit board artwork in which the area around the X0 and X1 pins is surrounded
by ground provides stable operation, such an arrangement is strongly recommended.
6. Sequence for Applying the A/D Converter Power Supply and the Analog Inputs
Always be sure to apply the digital power supply (V
CC
) before applying the A/D converter power supply (AV
CC
,
AVRH, and AVRL) and the analog inputs (AN0 to AN7).
In addition, when the power is turned off, turn off the A/D converter power supply and the analog inputs first,
and then turn off the digital power supply. (Turning on or off the analog and digital power supplies simultaneously
will not cause any problems.)
Whether applying or cutting off the power, be certain that AVRH does not exceed AV
CC
.
7. External Reset Input
To reliably reset the controller by inputting an “L” level to the RST pin, ensure that the “L” level is applied for at
least five machine cycles.
8. HST Pin
When turning on the system, be sure to set the HST pin to “H” level. Never set the HST pin to “L” level while the
RST pin is in “L” level.
9. CLK Pin
X1
X0
Note: CLK pin cannot use as I/O port.
Care must be taken that this is different from standard specification for F
2
MC-16F family.
ex. 50 MHz
CLK
STOP
Divide by 2 circuit
To internal blocks
STOP
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F244PFT-G | Octal Edge-Triggered D-type Flip-Flops With Clock Enable 20-LCCC -55 to 125 |
| MB90F334A | 16-bit Proprietary Microcontroller |
| MB90F334APFF | 16-bit Proprietary Microcontroller |
| MB90F334APMC | 16-bit Proprietary Microcontroller |
| MB90V330A | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F334APMC1-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC1-G-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SPE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。