- 您現在的位置：買賣IC網 > PDF目錄377922 > MB90F244 (Fujitsu Limited) Octal Edge-Triggered D-type Flip-Flops With Clock Enable 20-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90F244 |
| 廠商： | Fujitsu Limited |
| 英文描述： | Octal Edge-Triggered D-type Flip-Flops With Clock Enable 20-CFP -55 to 125 |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 14/67頁 |
| 文件大?。?/td> | 1403K |
| 代理商： | MB90F244 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
MB90F244
14
I
HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to the input or output
pins other than medium-and high-voltage pins or if higher than the voltage which shown on “1. Absolute Maximum
Ratings” in section “
I
Electrical Characteristics”is applied between V
CC
and V
SS
.
When latchup occurs, power supply current increases rapidly might thermally damage elements. When using,
take great care not to exceed the absolute maximum ratings.
In addition, for the same reasons take care to prevent the analog power supply from exceeding the digital power
supply.
2. Treatment of Unused Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistors.
3. Precautions when Using an External Clock
When an external clock is used, drive X0 only.
4. Power Supply Pins
When there are several V
CC
and V
SS
pins, those pins that should have the same electric potential are connected
within the device when the device is designed in order to prevent misoperation, such as latch-up. However, all
of those pins must be connected to the power supply and ground externally in order to reduce unnecessary
emissions, prevent misoperation of strobe signals due to an increase in the ground level, and to observe the
total output current standards.
In addition, give a due consideration to the connection in that current supply be connected to V
CC
and V
SS
with
the lowest possible impedance.
Finally, it is recommended to connect a capacitor of about 0.1
μ
F between V
CC
and V
SS
near this device as a
bypass capacitor.
For example an external clock
X0
X1
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F244PFT-G | Octal Edge-Triggered D-type Flip-Flops With Clock Enable 20-LCCC -55 to 125 |
| MB90F334A | 16-bit Proprietary Microcontroller |
| MB90F334APFF | 16-bit Proprietary Microcontroller |
| MB90F334APMC | 16-bit Proprietary Microcontroller |
| MB90V330A | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F334APMC1-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC1-G-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SPE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。