SPI/I2C UART with 128-Word FIFOs in WLP MAX3108 53 Maxim Integrated Low-Power Op" />
參數資料
型號: MAX3108EWA+T
廠商: Maxim Integrated Products
文件頁數: 49/56頁
文件大?。?/td> 0K
描述: IC UART
產品培訓模塊: Obsolescence Mitigation Program
標準包裝: 2,500
系列: *
SPI/I2C UART with 128-Word FIFOs in WLP
MAX3108
53
Maxim Integrated
Low-Power Operation
To reduce the power consumption during normal opera-
tion, the following techniques can be adopted:
Do not use the internal PLL. This saves the most
power of the options listed here. Disable and bypass
the PLL. With the PLL enabled, the current to the
VCC supply is in the range of a few mA (depending
on clock frequency and multiplication factor), while it
drops to below 1mA if disabled.
Use an external clock source. The lowest power
clocking mode is when an external clock signal is
used. This drops the power consumption to about half
that of an external crystal.
Keeptheinternalclockratesaslowaspossible.
UsealowvoltageontheVCC supply.
Use an external 1.8V supply. This saves the power
dissipated by the internal 1.8V linear regulator for the
1.8V core supply. Connect an external 1.8V supply to
V18 and disable the internal regulator by connecting
LDOEN to DGND.
Interrupts and Polling
Monitor the MAX3108 by polling the ISR register or by
monitoring the IRQ output. In polled mode, the IRQ physi-
cal interrupt output is not used and the host controller
polls the ISR register at frequent intervals to establish the
state of the MAX3108.
Alternatively, the physical IRQ interrupt can be used
to interrupt the host controller after specified events,
making polling unnecessary. The IRQ output is an open-
drain output that requires a pullup resistor to VL.
Logic-Level Translation
The MAX3108 can be directly connected to transceivers
and controllers that have different supply voltages. The VL
input defines the logic voltage levels of the controller inter-
face, while the VEXT voltage defines the logic of the trans-
ceiver interface. This ensures flexibility when selecting a
controller and transceiver. Figure 24 shows an example of
a configuration where the controller, transceiver, and the
MAX3108 are powered by three different supplies.
Figure 24. Logic-Level Translation
MAX3108
TX
RX
RTS
AGND
DGND
VL VCC
VEXT
RST
IRQ
SPI/I2C
MAX14840E
TRANSCEIVER
VCC
DI
DE
RO
VDD
2.5V
1.8V
3.3V
MICROCONTROLLER
相關PDF資料
PDF描述
MAX3109ETJ+ SEMICONDUCTOR OTHER
MAX310CPE IC VIDEO MULTIPLEXER 8X1 16DIP
MAX3110EENI+G36 IC UART SPI COMPAT 28-DIP
MAX3120CUA+ IC TXRX INFRARED IRDA 8-UMAX
MAX3120EUA IC TXRX 3V IRDA IR 3V 8-UMAX
相關代理商/技術參數
參數描述
MAX3109ETJ+ 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3109ETJ+T 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX310C/D 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX310CPE 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX310CPE+ 功能描述:多路器開關 IC 8:1 Unbuffered RF Video MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16