- 您現在的位置：買賣IC網 > PDF目錄17015 > MA330013 (Microchip Technology)MODULE PLUG-IN DSPIC33 100TQFP PDF資料下載
參數資料
| 型號： | MA330013 |
| 廠商： | Microchip Technology |
| 文件頁數： | 66/199頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE PLUG-IN DSPIC33 100TQFP |
| 標準包裝： | 1 |
| 附件類型： | 插拔式模塊（PIM）- dsPIC33FJ256MC710 |
| 適用于相關產品： | Explorer 16（DM240001 或 DM240002） |
| 產品目錄頁面： | 658 (CN2011-ZH PDF) |
| 配用： | DM330023-ND - BOARD DEV DSPICDEM MCHV |
| 相關產品： | DSPIC33FJ64MC710T-I/PT-ND - IC DSPIC MCU/DSP 64K 100TQFP DSPIC33FJ64MC710T-I/PF-ND - IC DSPIC MCU/DSP 64K 100TQFP DSPIC33FJ64MC510T-I/PT-ND - IC DSPIC MCU/DSP 64K 100TQFP DSPIC33FJ64MC510T-I/PF-ND - IC DSPIC MCU/DSP 64K 100TQFP DSPIC33FJ256MC510T-I/PT-ND - IC DSPIC MCU/DSP 256K 100TQFP DSPIC33FJ256MC510T-I/PF-ND - IC DSPIC MCU/DSP 256K 100TQFP DSPIC33FJ128MC710T-I/PT-ND - IC DSPIC MCU/DSP 128K 100TQFP DSPIC33FJ128MC710T-I/PF-ND - IC DSPIC MCU/DSP 128K 100TQFP DSPIC33FJ128MC510T-I/PT-ND - IC DSPIC MCU/DSP 128K 100TQFP DSPIC33FJ128MC510T-I/PF-ND - IC DSPIC MCU/DSP 128K 100TQFP 更多... |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁
dsPIC33F
DS70165E-page 156
Preliminary
2007 Microchip Technology Inc.
8.2
Clock Switching Operation
Applications are free to switch between any of the four
clock sources (Primary, LP, FRC and LPRC) under
software control at any time. To limit the possible side
effects that could result from this flexibility, dsPIC33F
devices have a safeguard lock built into the switch
process.
8.2.1
ENABLING CLOCK SWITCHING
To enable clock switching, the FCKSM1 Configuration
bit in the Configuration register must be programmed to
‘0’. (Refer to Section 23.1 “Configuration Bits” for
further details.) If the FCKSM1 Configuration bit is
unprogrammed (‘1’), the clock switching function and
Fail-Safe Clock Monitor function are disabled. This is
the default setting.
The NOSC control bits (OSCCON<10:8>) do not
control the clock selection when clock switching is
disabled. However, the COSC bits (OSCCON<14:12>)
reflect the clock source selected by the FNOSC
Configuration bits.
The OSWEN control bit (OSCCON<0>) has no effect
when clock switching is disabled. It is held at ‘0’ at all
times.
8.2.2
OSCILLATOR SWITCHING
SEQUENCE
At a minimum, performing a clock switch requires this
basic sequence:
1.
If
desired,
read
the
COSC
bits
(OSCCON<14:12>) to determine the current
oscillator source.
2.
Perform the unlock sequence to allow a write to
the OSCCON register high byte.
3.
Write the appropriate value to the NOSC control
bits (OSCCON<10:8>) for the new oscillator
source.
4.
Perform the unlock sequence to allow a write to
the OSCCON register low byte.
5.
Set the OSWEN bit to initiate the oscillator
switch.
Once the basic sequence is completed, the system
clock hardware responds automatically as follows:
1.
The clock switching hardware compares the
COSC status bits with the new value of the
NOSC control bits. If they are the same, then the
clock switch is a redundant operation. In this
case, the OSWEN bit is cleared automatically
and the clock switch is aborted.
2.
If a valid clock switch has been initiated, the
LOCK
(OSCCON<5>)
and
the
CF
(OSCCON<3>) status bits are cleared.
3.
The new oscillator is turned on by the hardware
if it is not currently running. If a crystal oscillator
must be turned on, the hardware waits until the
Oscillator Start-up Timer (OST) expires. If the
new source is using the PLL, the hardware waits
until a PLL lock is detected (LOCK = 1).
4.
The hardware waits for 10 clock cycles from the
new clock source and then performs the clock
switch.
5.
The hardware clears the OSWEN bit to indicate a
successful clock transition. In addition, the NOSC
bit values are transferred to the COSC status bits.
6.
The old clock source is turned off at this time,
with the exception of LPRC (if WDT or FSCM
are enabled) or LP (if LPOSCEN remains set).
8.3
Fail-Safe Clock Monitor (FSCM)
The Fail-Safe Clock Monitor (FSCM) allows the device
to continue to operate even in the event of an oscillator
failure. The FSCM function is enabled by programming.
If the FSCM function is enabled, the LPRC internal
oscillator runs at all times (except during Sleep mode)
and is not subject to control by the Watchdog Timer.
In the event of an oscillator failure, the FSCM
generates a clock failure trap event and switches the
system clock over to the FRC oscillator. Then the
application program can either attempt to restart the
oscillator or execute a controlled shutdown. The trap
can be treated as a warm Reset by simply loading the
Reset address into the oscillator fail trap vector.
If the PLL multiplier is used to scale the system clock,
the internal FRC is also multiplied by the same factor
on clock failure. Essentially, the device switches to
FRC with PLL on a clock failure.
Note:
Primary Oscillator mode has three different
submodes (XT, HS and EC) which are
determined by the POSCMD<1:0> Config-
uration bits. While an application can
switch to and from Primary Oscillator
mode
in
software,
it
cannot
switch
between the different primary submodes
without reprogramming the device.
Note 1: The processor continues to execute code
throughout the clock switching sequence.
Timing sensitive code should not be
executed during this time.
2: Direct clock switches between any primary
oscillator mode with PLL and FRCPLL
mode are not permitted. This applies to
clock switches in either direction. In these
instances, the application must switch to
FRC mode as a transition clock source
between the two PLL modes.
相關PDF資料 |
PDF描述 |
|---|---|
| ACM06DRUH | CONN EDGECARD 12POS .156 DIP SLD |
| MA180013 | MODULE PLUG-IN 18F45J10 44TQFP |
| VE-JW1-EY | CONVERTER MOD DC/DC 12V 50W |
| GEM06DTBN-S664 | CONN EDGECARD 12POS R/A .156 SLD |
| AC162057 | MPLAB ICD 2 HEADER 14DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MA330014 | 功能描述:子卡和OEM板 dsPIC33 MC RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA330015 | 功能描述:子卡和OEM板 dsPIC33 GP RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA330016 | 功能描述:子卡和OEM板 dsPIC33F GP RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA330017 | 功能描述:子卡和OEM板 dsPIC33F MC RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA330018 | 功能描述:子卡和OEM板 44P QFN TO 100P PIM dsPIC33FJ128MC804 RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
發布緊急采購，3分鐘左右您將得到回復。