參數資料
型號： M58WR064EB85ZB6T
廠商： NUMONYX
元件分類： PROM
英文描述： 4M X 16 FLASH 1.8V PROM, 85 ns, PBGA56
封裝： 7.70 X 9 MM, 0.75 MM PITCH, VFBGA-56
文件頁數： 25/81頁
文件大?。?/td> 539K
代理商： M58WR064EB85ZB6T
31/81
M58WR064ET, M58WR064EB
READ MODES
Read operations can be performed in two different
ways depending on the settings in the Configura-
tion Register. If the clock signal is ‘don’t care’ for
the data output, the read operation is Asynchro-
nous; if the data output is synchronized with clock,
the read operation is Synchronous.
The Read mode and data output format are deter-
mined by the Configuration Register. (See Config-
uration Register section for details). All banks
supports both asynchronous and synchronous
read operations. The Multiple Bank architecture
allows read operations in one bank, while write op-
erations are being executed in another (see Ta-
bles 11 and 12).
Asynchronous Read Mode
In Asynchronous Read operations the clock signal
is ‘don’t care’. The device outputs the data corre-
sponding to the address latched, that is the mem-
ory
array,
Status
Register,
Common
Flash
Interface or Electronic Signature depending on the
command issued. CR15 in the Configuration Reg-
ister must be set to ‘1’ for Asynchronous opera-
tions.
In Asynchronous Read mode a Page of data is in-
ternally read and stored in a Page Buffer. The
Page has a size of 4 Words and is addressed by
A0 and A1 address inputs. The address inputs A0
and A1 are not gated by Latch Enable in Asyn-
chronous Read mode.
The first read operation within the Page has a
longer access time (Tacc, Random access time),
subsequent reads within the same Page have
much shorter access times. If the Page changes
then the normal, longer timings apply again.
Asynchronous Read operations can be performed
in two different ways, Asynchronous Random Ac-
cess Read and Asynchronous Page Read. Only
Asynchronous Page Read takes full advantage of
the internal page storage so different timings are
applied.
See Table 20, Asynchronous Read AC Character-
istics, Figure 10, Asynchronous Random Access
Read AC Waveform and Figure 11, Asynchronous
Page Read AC Waveform for details.
Synchronous Burst Read Mode
In Synchronous Burst Read mode the data is out-
put in bursts synchronized with the clock. It is pos-
sible
to
perform
burst
reads
across
bank
boundaries.
Synchronous Burst Read mode can only be used
to read the memory array. For other read opera-
tions, such as Read Status Register, Read CFI
and Read Electronic Signature, Single Synchro-
nous Read or Asynchronous Random Access
Read must be used.
In Synchronous Burst Read mode the flow of the
data output depends on parameters that are con-
figured in the Configuration Register.
A burst sequence is started at the first clock edge
(rising or falling depending on Valid Clock Edge bit
CR6 in the Configuration Register) after the falling
edge of Latch Enable. Addresses are internally in-
cremented and after a delay of 2 to 5 clock cycles
(X latency bits CR13-CR11) the corresponding
data are output on each clock cycle.
The number of Words to be output during a Syn-
chronous Burst Read operation can be configured
as 4 or 8 Words or Continuous (Burst Length bits
CR2-CR0). The data can be configured to remain
valid for one or two clock cycles (Data Output Con-
figuration bit CR9).
The order of the data output can be modified
through the Burst Type and the Wrap Burst bits in
the Configuration Register. The burst sequence
may be configured to be sequential or interleaved
(CR7). The burst reads can be confined inside the
4 or 8 Word boundary (Wrap) or overcome the
boundary (No Wrap). If the starting address is
aligned to a 4 Word Page the wrapped configura-
tion has no impact on the output sequence. Inter-
leaved mode is not allowed in Continuous Burst
Read mode or with No Wrap sequences.
A WAIT signal may be asserted to indicate to the
system that an output delay will occur. This delay
will depend on the starting address of the burst se-
quence; the worst case delay will occur when the
sequence is crossing a 64 word boundary and the
starting address was at the end of a four word
boundary.
WAIT is asserted during X latency and the Wait
state and is only deasserted when output data are
valid. In Continuous Burst Read mode a Wait state
will occur when crossing the first 64 Word bound-
ary. If the burst starting address is aligned to a 4
Word Page, the Wait state will not occur.
The WAIT signal can be configured to be active
Low or active High (default) by setting CR10 in the
Configuration Register. The WAIT signal is mean-
ingful only in Synchronous Burst Read mode, in
other modes, WAIT is always asserted (except for
Read Array mode).
See Table 21, Synchronous Read AC Character-
istics and Figure 12, Synchronous Burst Read AC
Waveform for details.
Single Synchronous Read Mode
Single Synchronous Read operations are similar
to Synchronous Burst Read operations except that
only the first data output after the X latency is valid.
Other Configuration Register parameters have no
effect on Single Synchronous Read operations.
相關PDF資料
PDF描述
M58WR064KU70ZA6U 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44
M5L28FGNFREQ CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT
M3L13TCNFREQ CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT
M3L14FCNFREQ CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT
M3L15TGNFREQ CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT
相關代理商/技術參數
參數描述
M58WR064EBZB 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit 4Mb x 16, Multiple Bank, Burst 1.8V Supply Flash Memory
M58WR064ET 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit 4Mb x 16, Multiple Bank, Burst 1.8V Supply Flash Memory
M58WR064ET10ZB6T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit 4Mb x 16, Multiple Bank, Burst 1.8V Supply Flash Memory
M58WR064ET70ZB6T 功能描述:閃存 64M (4Mx16) 70ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M58WR064ET80ZB6T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit 4Mb x 16, Multiple Bank, Burst 1.8V Supply Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*