參數資料
型號: M38K07M4L-XXXHP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP64
封裝: 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
文件頁數: 116/133頁
文件大?。?/td> 1359K
代理商: M38K07M4L-XXXHP
38K0 Group
Rev.3.00
Oct 05, 2006
page 83 of 129
REJ03B0192-0300
Outline Performance (CPU Rewrite Mode)
CPU rewrite mode is usable in the single-chip or Boot mode. The
only User ROM area can be rewritten in CPU rewrite mode.
In CPU rewrite mode, the CPU erases, programs and reads the in-
ternal flash memory as instructed by software commands. This
rewrite control program must be transferred to a memory such as
the internal RAM before it can be executed.
The MCU enters CPU rewrite mode by applying 4.50 V to 5.25 V
to the CNVSS pin and setting “1” to the CPU Rewrite Mode Select
Bit (bit 1 of address 0FFE16). Software commands are accepted
once the mode is entered.
Use software commands to control program and erase operations.
Whether a program or erase operation has terminated normally or
in error can be verified by reading the status register.
Figure 117 shows the flash memory control register.
Bit 0 is the RY/BY status flag used exclusively to read the operat-
ing status of the flash memory. During programming and erase
operations, it is “0” (busy). Otherwise, it is “1” (ready). This is
equivalent to the RY/BY pin function in parallel I/O mode.
Bit 1 is the CPU Rewrite Mode Select Bit. When this bit is set to
“1”, the MCU enters CPU rewrite mode. Software commands are
accepted once the mode is entered. In CPU rewrite mode, the
Flash memory control register (address 0FFE16)
FMCR (Note 1)
RY/BY status flag
0: Busy (being written or erased)
1: Ready
CPU rewrite mode select bit (Note 2)
0: Normal mode (Software commands invalid)
1: CPU rewrite mode (Software commands acceptable)
CPU rewrite mode entry flag
0: Normal mode (Software commands invalid)
1: CPU rewrite mode
Flash memory reset bit (Note 3)
0: Normal operation
1: Reset
User area / Boot area select bit (Note 4)
0: User ROM area accessed
1: Boot ROM area accessed
Reserved bits (indefinite at read/ “0” at write)
b0
b7
Notes1: The contents of flash memory control register are “XXX00001” just after reset release.
2: For this bit to be set to “1”, the user needs to write “0” and then “1” to it in succession. If it is not
this procedure, this bit will not be set to ”1”. Additionally, it is required to ensure that no interrupt
will be generated during that interval.
Use the control program in the area except the built-in flash memory for write to this bit.
3: This bit is valid when the CPU rewrite mode select bit is “1”. Set this bit 3 to “0” subsequently after
setting bit 3 to “1”.
4: Use the control program in the area except the built-in flash memory for write to this bit.
CPU becomes unable to access the internal flash memory directly.
Therefore, use the control program in a memory other than inter-
nal flash memory for write to bit 1. To set this bit to “1”, it is
necessary to write “0” and then write “1” in succession. The bit can
be set to “0” by only writing “0”.
Bit 2 is the CPU Rewrite Mode Entry Flag. This flag indicates “1” in
CPU rewrite mode, so that reading this flag can check whether
CPU rewrite mode has been entered or not.
Bit 3 is the flash memory reset bit used to reset the control circuit
of internal flash memory. This bit is used when exiting CPU rewrite
mode and when flash memory access has failed. When the CPU
Rewrite Mode Select Bit is “1”, setting “1” for this bit resets the
control circuit. To set this bit to “1”, it is necessary to write “0” and
then write “1” in succession. To release the reset, it is necessary
to set this bit to “0”.
Bit 4 is the User Area/Boot Area Select Bit. When this bit is set to
“1”, Boot ROM area is accessed, and CPU rewrite mode in Boot
ROM area is available. In Boot mode, this bit is set to “1” auto-
matically. Reprogramming of this bit must be in a memory other
than internal flash memory.
Figure 118 shows a flowchart for setting/releasing CPU rewrite
mode.
Fig. 117 Structure of flash memory control register
相關PDF資料
PDF描述
M38K09F8LHP 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP64
M38K09F8LFP 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP64
M38K07M4L-XXXFP 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP64
M38K29F8LFP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
M38K29F8HP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38K09F8LFP 功能描述:IC 740 MCU FLASH 32K 64LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C,IrDA,SPI,UART/USART 外圍設備:欠壓檢測/復位,DMA,POR,PWM,WDT 輸入/輸出數:50 程序存儲器容量:192KB(96K x 16) 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
M38K09F8LFP#U0 制造商:Renesas Electronics Corporation 功能描述:MCU 8-bit 740 CISC 32KB Flash 5V 64-Pin LQFP Tray 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 32K 64-LQFP LEAD FREE - Trays
M38K09F8LHP 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 64LQFP - Trays 制造商:Renesas Electronics Corporation 功能描述:IC,microcomputer,USB,LQFP64,12
M38K09F8LHP#U0 功能描述:MCU 3/5V 32K PB-FREE AH570264-LQ RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI,I²C,IEBus,IrDA,SIO,UART/USART 外圍設備:DMA,POR,PWM,WDT 輸入/輸出數:121 程序存儲器容量:384KB(384K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b,D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
M38K09RFS 功能描述:EMULATOR MCU FOR 38K0 GROUP RoHS:否 類別:編程器,開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*