參數資料
型號： M38503M4H
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 48/86頁
文件大?。?/td> 1193K
代理商： M38503M4H
48
3850 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Bus Operation Modes
Read
The Read mode is entered by pulling the OE pin low when the CE
pin is low and the WE and RP pins are high. There are two read
modes: array, and status register, which are selected by software
command input. In read mode, the data corresponding to each soft-
ware command entered is output from the data I/O pins D
0
–
D
7
. The
read array mode is automatically selected when the device is pow-
ered on or after it exits deep power down mode.
Output Disable
The output disable mode is entered by pulling the CE pin low and the
WE, OE, and RP pins high. Also, the data I/O pins are placed in the
high-impedance state.
Standby
The standby mode is entered by driving the CE pin high when the RP
pin is high. Also, the data I/O pins are placed in the high-impedance
state. However, if the CE pin is set high during erase or program
operation, the internal control circuit does not halt immediately and
normal power consumption is required until the operation under way
is completed.
Write
The write mode is entered by pulling the WE pin low when the CE pin
is low and the OE and RP pins are high. In this mode, the device
accepts the software commands or write data entered from the data
I/O pins. A program, erase, or some other operation is initiated de-
pending on the content of the software command entered here. The
input data such as address and software command is latched at the
rising edge of WE or CE whichever occurs earlier.
Deep Power Down
The deep power down is entered by pulling the RP pin low. Also, the
data I/O pins are placed in the high-impedance state. When the de-
vice is freed from deep power down mode, the read array mode is
“
80
16
.
”
If the
RP pin is pulled low during erase or program operation, the opera-
tion under way is canceled and the data in the relevant block be-
comes invalid.
User ROM and Boot ROM Areas
In parallel I/O mode, the user ROM and boot ROM areas shown in Fig-
ure 44 can be rewritten. The BSEL pin is used to choose between these
two areas. The user ROM area is selected by pulling the BSEL input
low; the boot ROM area is selected by driving the BSEL input high. Both
areas of flash memory can be operated on in the same way.
Program and block erase operations can be performed in the user ROM
area. The user ROM area and its block is shown in Figure 44.
The user ROM area is 32 Kbytes in size. In parallel I/O mode, it is
located at addresses 8000
16
through FFFF
16
. The boot ROM area is
4 Kbytes in size. In parallel I/O mode, it is located at addresses
F000
16
through FFFF
16
. Make sure program and block erase opera-
tions are always performed within this address range. (Access to any
location outside this address range is prohibited.)
In the Boot ROM area, an erase block operation is applied to only
one 4 Kbyte block. The boot ROM area has had a standard serial I/O
mode control program stored in it when shipped from the Mitsubishi
factory. Therefore, using the device in standard serial input/output
mode, you do not need to write to the boot ROM area.
Functional Outline (Parallel I/O Mode)
In parallel I/O mode, bus operation modes
—
Read, Output Disable,
Standby, Write, and Deep Power Down
—
are selected by the status
of the CE, OE, WE, and RP input pins.
The contents of erase, program, and other operations are selected
by writing a software command. The data, status register, etc. in
memory can only be read out by a read after software command
input.
Program and erase operations are controlled using software com-
mands.
The following explains about bus operation modes, software com-
mands, and status register.
D
0
to D
7
Data output
Status register data output
High impedance
High impedance
Command/data input
Command input
Command input
High impedance
RP
V
IH
V
IH
V
IH
V
IH
V
IH
V
IH
V
IH
V
IL
______
V
IH
V
IH
V
IH
X
V
IL
V
IL
V
IL
X
OE
V
IL
V
IL
V
IH
X
V
IH
V
IH
V
IH
X
CE
V
IL
V
IL
V
IL
V
IH
V
IL
V
IL
V
IL
X
Pin name
Mode
Array
Status register
Output disabled
Stand by
Program
Erase
Other
Write
Deep power down
Note : X can be V
IL
or V
IH
.
Read
Table 12 Relationship between control signals and bus operation modes
Parallel I/O Mode
The parallel I/O mode is entered by making connections shown in
Figure 52 and then turning the Vcc power supply on.
Address
The user ROM is only one block as shown in Figure 44. The block
address referred to in this data sheet is the maximum address value
of each block.
相關PDF資料
PDF描述
M38513M4 Hook-Up Wire; Conductor Size AWG:26; No. Strands x Strand Size:7 x 34; Jacket Color:Dark Blue; Approval Bodies:UL, CSA; Approval Categories:UL AWM Style 1061; CSA AWM; Conductor Material:Copper RoHS Compliant: Yes
M38513M4-C56FP Hook-Up Wire; Conductor Size AWG:28; No. Strands x Strand Size:7 x 36; Jacket Color:Red; Approval Bodies:UL, CSA; Approval Categories:UL AWM Style 1061; CSA AWM; Conductor Material:Copper; Jacket Material:Polyvinylchloride (PVC) RoHS Compliant: Yes
M3851 Single Chip 8 Bits Microcomputer(8位單片機)
M38512M4 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M388504E6SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38504E6FP 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 24K 42-SSOP - Trays
M38504E6FP#U0 功能描述:MCU 4.0/5.5V 24K PB-FREE 42-SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
M38504M6202F 制造商:Panasonic Industrial Company 功能描述:SUB ONLY IC
M38504M6211F 制造商:Panasonic Industrial Company 功能描述:IC SUB FOR P-M38504M6202F
M38507ARLSS 功能描述:M-SUPPORT TOOL RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*