- 您現在的位置：買賣IC網 > PDF目錄67763 > M37643F8FP 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37643F8FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 18/120頁 |
| 文件大小： | 1253K |
| 代理商： | M37643F8FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
114
7643 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to
change.
USB
When the USB Reset Interrupt Status Flag is kept at “1”, all other
flags in the USB internal registers (addresses 005016 to 005F16)
will return to their reset status. However, the following registers
are not affected by the USB reset: USB control register (address
001316), Frequency synthesizer control register (address
006C16), Clock control register (address 001F16), and USB end-
point-x FIFO register (addresses 006016 to 006216).
When not using the USB function, set the USB Line Driver Supply
Enable Bit of the USB control register (address 001316) to “1” for
power supply to the internal circuits (at Vcc = 5V).
The IN_PKT_RDY Bit can be set by software even when using
the AUTO_SET function.
When writing to USB-related registers, set the USB Clock Enable
Bit to “1”, then perform the write after four
φ cycle waits.
The receive buffer full interrupt request is not generated if receive
errors are detected at receiving.
If a character bit length is 7 bits, bit 7 of the UART transmit/re-
ceive buffer register 1 and bits 0 to 7 of the UART transmit/
receive buffer register 2 are ignored at transmitting; they are in-
valid at receiving.
If a character bit length is 8 bits, bits 0 to 7 of the UART transmit/
receive buffer register 2 are ignored at transmitting; they are in-
valid at receiving.
If a character bit length is 9 bits, bits 1 to 7 of the UART transmit/
receive buffer register 2 are ignored at transmitting; they are “0”
at receiving.
When using the MCU at Vcc = 3.3V, set the USB Line Driver Sup-
ply Enable Bit to “0” (line driver disable). Note that setting the
USB Line Driver Current Control Bit (USBC3) doesn’t affect the
USB operation.
Read one packet data from the OUT FIFO before clearing the
OUT_PKT_RDY Flag. If the OUT_PKT_RDY Flag is cleared
while one packet data is being read, the internal read pointer can-
not operate normally.
Use the transfer instructions such as LDA and STA to set the reg-
isters: USB interrupt status registers 1, 2 (addresses 005216,
005316); USB endpoint 0 IN control register (address 005916);
USB endpoint x IN control register (address 005916); USB end-
point x OUT control register (address 005A16). Do not use the
read-modify-write instructions such as the SEB or the CLB in-
struction.
When writing to bits shown by Table 27 using the transfer instruc-
tion such as LDA or STA, a value which never affect its bit state
is required. Take the following sequence to change these bits
contents:
(1) Store the register contents onto a variable or a data register.
(2) Change the target bit on the variable or the data register. Si-
multaneously mask the bit so that its bit state cannot be
changed. (See to Table 27.)
(3) Write the value from the variable or the data register to the
register using the transfer instruction such as LDA or STA.
Table 27 Bits of which state might be changed owing to software write
Register name
USB endpoint 0 IN control register
USB endpoint x (x = 1, 2) IN control register
USB endpoint x (x = 1, 2) OUT control register
Bit name
IN_PKT_RDY (b1)
DATA_END (b3)
FORCE_STALL (b4)
IN_PKT_RDY (b0)
UNDER_RUN (b1)
OUT_PKT_RDY (b0)
OVER_RUN (b1)
FORCE_STALL (b4)
DATA_ERR (b5)
Value not affecting state (Note)
“0”
“1”
“0”
“1”
Note: Writing this value will not change the bit state, because this value cannot be written to the bit by software.
相關PDF資料 |
PDF描述 |
|---|---|
| M37643F8HP | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37643M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37702S1LGP | 16-BIT, 8 MHz, MICROCONTROLLER, PQFP80 |
| M37702M2LXXXGP | 16-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| M37702M2LXXXHP | 16-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37643F8M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37643M8E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37643M8M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M3764A-12 | 制造商:OK International 功能描述: |
| M3765 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HORN/SIREN WITH SOFT CHIRP 6 ALARM SOUNDS |
發布緊急采購，3分鐘左右您將得到回復。