- 您現在的位置：買賣IC網 > PDF目錄69014 > M37640M8-XXXFP 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37640M8-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 39/96頁 |
| 文件大?。?/td> | 1477K |
| 代理商： | M37640M8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
44
Ver 1.4
MITSUBISHI MICROCOMPUTERS
7640 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Reserved
OER
FER
PER
RBF
TBE
TCM
MSB
7
LSB
0
Address: 0032
16 ,003A16
Access: Read only
Reset: 03
16
SER
TCM
Transmission complete (Transmission Register empty) Flag (Bit 0)
0: Data in Transmission Register
1: No data in Transmission Register
TBE
TX Buffer Empty flag (Bit 1)
0: Data in TX Buffer
1: No data in the TX Buffer
RBF
RX Buffer Full Flag (Bit 2)
0: No data in RX Buffer
1: Data in RX Buffer
PER
Receive Parity Error Flag (Bit 3)
0: No parity error received
1: Received framing error
FER
Receive Framing Error Flag (Bit 4)
0: No framing error received
1: Received framing error
OER
Receive Overrun Flag (Bit 5)
0: No overrun receive received
1: Received overrun
SER
Receive Error Sum flag (Bit 6)
0: No error received
1: Received error
Bit 7
Reserved (Read “0”)
Fig. 1.44. UART Status Register (U1STS, U2STS)
1.19.4 Transmit/Receive Methods
1.19.4.1 Transmit Method
Setup
Define the baud rate by writing a value from 0-255 into
the UxBRG (see Figure 1.45).
Set the Transmission Initialization Bit (TIN, bit 2 of
UxCON), to “1”. This will reset the transmit status to a
value of 0316.
Select the interrupt source to be either TBE or TCM
by clearing or setting the Transmit Interrupt Source Se-
lection Bit (TIS, bit 4 of UxCON).
Configure the data format and clock selection by writ-
ing the appropriate value to UxMOD.
Set the Clear-To-Send Enable Bit (CTS_SEL, bit 5 of
UxCON), if CTS handshaking will be used.
Set the Transmit Enable Bit (TEN, bit 0 of UxCON), to
“1”.
Operation
When data is written to the low-order byte of the trans-
mit buffer (UxTRB1), TBE is cleared to “0”. If 9-bit
character length has been selected, the high-order byte
of the transmit buffer (UxTRB2) should be written before
the low-order byte (UxTRB1).
If no data is being shifted out of the transmit shift reg-
ister and CTS handshaking is disabled, the data written
to the transmit buffer is transferred to the transmit shift
register and the TCM flag in UxSTS is cleared to a “0”.
In addition, the TBE flag is set to a “1”, signaling that
the next byte of data can be written to the transmit
buffer. If CTS handshaking is enabled, the operation de-
scribed above does not take place until CTSx is
brought low.
Data from the transmit shift register is transmitted one
bit at a time beginning with the start bit and ending with
the stop bit. Note that the LSB is transmitted first.
If the TEN bit is cleared to a “0” while data is still be-
ing transmitted, the transmitter will continue until the
last bit is sent. This is also the case when CTS hand-
shaking is enabled and CTSx is brought back high
during transmission.
When the last bit is transmitted, the TCM flag is set to
a “1” if the transmit buffer is empty, TEN is a “0”, or
CTS handshaking is enabled and CTSx is “1”. If the
transmit buffer is not empty, TEN is a “1”, and CTS
handshaking is disabled or CTS handshaking is en-
abled and CTSx is low, the TCM flag is not set
because transfer of the contents of the transmit buffer
to the transmit shift register occurs immediately.
相關PDF資料 |
PDF描述 |
|---|---|
| M37640E8FP | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37643M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37643F8HP | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37700E2AFS | 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC80 |
| M37700E2AXXXFP | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37641F8E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8FP#U0 | 功能描述:IC 740 MCU FLASH 32K 80QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| M37641F8HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8HP#U0 | 功能描述:IC 740 MCU FLASH 32K 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 產品培訓模塊:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 標準包裝:27 系列:PIC® 24H 核心處理器:PIC 芯體尺寸:16-位 速度:40 MIP 連通性:I²C，SPI，UART/USART 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:21 程序存儲器容量:12KB（4K x 24） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 3.6 V 數據轉換器:A/D 10x10b/12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 包裝:管件 產品目錄頁面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2 |
發布緊急采購，3分鐘左右您將得到回復。