- 您現在的位置：買賣IC網 > PDF目錄359059 > M37544 (Renesas Technology Corp.) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37544 |
| 廠商： | Renesas Technology Corp. |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 65/68頁 |
| 文件大?。?/td> | 579K |
| 代理商： | M37544 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁
7544 Group
Rev.1.04 2004.06.08 page 65 of 66
REJ03B0012-0104Z
Notes on Clock Generating Circuit
1. Switch of ceramic/quartz-crystal oscillation and RC oscillation
After releasing reset, the oscillation mode selection bit (bit 5 of
CPU mode register (address 3B
16
)) is “0” (ceramic/quartz-crystal
oscillation selected). When the RC oscillation is used, after releas-
ing reset, set this bit to “1”.
2. Double-speed mode
The double-speed mode can be used only when a ceramic oscilla-
tion is selected. Do not use it when an RC oscillation is selected.
3. CPU mode register
Oscillation mode selection bit (bit 5), processor mode bits (bits 1
and 0) of CPU mode register (address 3B
16
) are used to select os-
cillation mode and to control operation modes of the
microcomputer. In order to prevent the dead-lock by erroneously
writing (ex. program run-away), these bits can be rewritten only
once after releasing reset. After rewriting, it is disabled to write any
data to the bit. (The emulator MCU “M37542RSS” is excluded.)
Also, when the read-modify-write instructions (SEB, CLB, etc.) are
executed to bits 2 to 4, 6 and 7, bits 5, 1 and 0 are locked.
4. Clock division ratio, X
IN
oscillation control, on-chip oscillator
control
The state transition shown in Fig. 81 can be performed by setting
the clock division ratio selection bits (bits 7 and 6), X
IN
oscillation
control bit (bit 4), on-chip oscillator oscillation control bit (bit 3) of
CPU mode register. Be careful of notes on use in Fig. 81.
5. On-chip oscillator operation
When the MCU operates by the on-chip oscillator for the main
clock, connect X
IN
pin to V
CC
through a 1 k
to 10 k
resistor and
leave X
OUT
pin open.
The clock frequency of the on-chip oscillator depends on the sup-
ply voltage and the operation temperature range.
Be careful that this margin of frequencies when designing applica-
tion products.
6. Ceramic resonator
When the ceramic resonator/quartz-crystal oscillation is used for
the main clock, connect the ceramic resonator and the external
circuit to pins X
IN
and X
OUT
at the shortest distance. A feedback
resistor is built-in.
7. RC oscillation
When the RC oscillation is used for the main clock, connect the
X
IN
pin and X
OUT
pin to the external circuit of resistor R and the
capacitor C at the shortest distance.
The frequency is affected by a capacitor, a resistor and a micro-
computer.
So, set the constants within the range of the frequency limits.
8. External clock
When the external signal clock is used for the main clock, connect
the X
IN
pin to the clock source and leave X
OUT
pin open.
Select “0” (ceramic oscillation) to oscillation mode selection bit.
Notes on Oscillation Control
1. Oscillation stop detection circuit
(1) When the stop mode is used, set the oscillation stop detection
function to “invalid”.
(2) When the ceramic or RC oscillation is stopped (bit 4 of CPU
mode register (address 3B
16
)), set the oscillation stop detec-
tion function to “invalid”.
(3) The oscillation stop detection circuit is not included in the emu-
lator MCU “M37542RSS”.
2. Stop mode
(1) When the stop mode is used, set the oscillation stop detection
function to “invalid”.
(2) When the stop mode is used, set “0” (
STP
instruction enabled)
to the
STP
instruction disable bit of the watchdog timer control
register (bit 6 of watchdog timer control register (address
39
16
)).
(3) The oscillation stabilizing time after release of
STP
instruction
can be selected from “set automatically”/“not set automati-
cally” by the oscillation stabilizing time set bit after release of
the
STP
instruction (bit 0 of MISRG (address 38
16
)). When “0”
is set to this bit, “01
16
” is set to timer 1 and “FF
16
” is set to
prescaler 1 automatically at the execution of the STP instruc-
tion. When “1” is set to this bit, set the wait time to timer 1 and
prescaler 1 according to the oscillation stabilizing time of the
oscillation. Also, when timer 1 is used, set values again to
timer 1 and prescaler 1 after system is returned from the stop
mode.
(4) The STP instruction cannot be used when the on-chip oscilla-
tor is selected by the clock division ratio selection bits (bits 7
and 6 of CPU mode register (address 3B
16
)).
(5) When the stop mode is used, set the on-chip oscillator oscilla-
tion control bit (bit 3 of CPU mode register (address 3B
16
)) to
“1” (on-chip oscillator oscillation stop).
(6) Do not execute the
STP
instruction during the A/D conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| M37548G1FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37549G1FP | 32K x 8 Static RAM; Density: 256 Kb; Organization: 32Kb x 8; Vcc (V): 4.5 to 5.5 V; |
| M38030F2L-XXXWG | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38122E7-XXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38232GC-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37544G2AGP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 8KB ROM 5V 32LQFP - Trays |
| M37544G2AGP#U0 | 功能描述:IC 740 MCU OTP 8K 32LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction AVR® UC3 Introduction 標準包裝:2,500 系列:AVR®32 UC3 B 核心處理器:AVR 芯體尺寸:32-位 速度:60MHz 連通性:I²C，IrDA，SPI，SSC，UART/USART，USB 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:28 程序存儲器容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:32K x 8 電壓 - 電源 (Vcc/Vdd):1.65 V ~ 1.95 V 數據轉換器:A/D 6x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 包裝:帶卷 (TR) 配用:ATSTK600-TQFP48-ND - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1101-ND - KIT DEV/EVAL FOR AVR32 AT32UC3B 其它名稱:AT32UC3B1128-AUR-NDAT32UC3B1128-AURTR |
| M37544G2ASP#U0 | 功能描述:MCU 2/5V 8K 32-SDIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M37544G2GP | 功能描述:IC 740 MCU OTP 8K 32LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| M37544G2HP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。