- 您現在的位置：買賣IC網 > PDF目錄69013 > M37517F8HP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M37517F8HP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 59/100頁 |
| 文件大?。?/td> | 899K |
| 代理商： | M37517F8HP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
Rev.1.01
Aug 02, 2004
page 59 of 96
7517 Group
(1) CPU Rewrite Mode
In CPU rewrite mode, the internal flash memory can be operated
on (read, program, or erase) under control of the Central Process-
ing Unit (CPU).
In CPU rewrite mode, only the User ROM area shown in Figure 64
can be rewritten; the Boot ROM area cannot be rewritten. Make
sure the program and block erase commands are issued for only
the User ROM area and each block area.
The control program for CPU rewrite mode can be stored in either
User ROM or Boot ROM area. In the CPU rewrite mode, because
the flash memory cannot be read from the CPU, the rewrite con-
trol program must be transferred to internal RAM area to be
executed before it can be executed.
Microcomputer Mode and Boot Mode
The control program for CPU rewrite mode must be written into
the User ROM or Boot ROM area in parallel I/O mode beforehand.
(If the control program is written into the Boot ROM area, the stan-
dard serial I/O mode becomes unusable.)
See Figure 64 for details about the Boot ROM area.
Normal microcomputer mode is entered when the microcomputer
is reset with pulling CNVSS pin low. In this case, the CPU starts
operating using the control program in the User ROM area.
When the microcomputer is reset by pulling the P41/INT0 pin high,
the CNVss pin high, the CPU starts operating using the control
program in the Boot ROM area (program start address is FFFC16,
FFFD16 fixation). This mode is called the “Boot” mode.
The User ROM area can be rewritten also by the control program
in the Boot ROM area.
Block Address
Block addresses refer to the maximum address of each block.
These addresses are used in the block erase command. In case
of the M37517F8, it has only one block.
相關PDF資料 |
PDF描述 |
|---|---|
| M37532RSS | 8-BIT, 6 MHz, MICROCONTROLLER |
| M37544G2GP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37544M2-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37544M2-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37544M2-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37530T-PTC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 42-pin 1.778mm-pitch SDIP to a 40-pin Narrow-pitch Connector (for 7531, 7540, 7542 and 7544 Groups) |
| M37530T-PTCB | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 40-pin Narrow-pitch Connector to 32-pin 0.8mm-pitch LQFP (for 7531, 7532, 7534, 7540, 7542 and 7544 Groups) |
| M37530T-PTCC | 功能描述:DEV 42-PIN RSS/MCU TO 32-PIN 1.7 RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37531E4FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4FP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MITSUBISHI 8 BIT OTP MCU |
發布緊急采購，3分鐘左右您將得到回復。