- 您現在的位置：買賣IC網 > PDF目錄69013 > M37517F8HP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M37517F8HP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 40/100頁 |
| 文件大?。?/td> | 899K |
| 代理商： | M37517F8HP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
Rev.1.01
Aug 02, 2004
page 42 of 96
7517 Group
Notes on current integrator
When changing current integration into prohibition from permis-
sion, incorrect interrupt may occur. Perform any one of the
following by software as the measure.
(1) How to control timing which disable current integrator
When changing current integration to prohibition in the current in-
tegrate mode, change the setting during “H” of the clock signal
which operates in a cycle of 125 ms.
When changing current integration to prohibition in the calibration
mode, change the setting during “H” of the clock signal operated
by cycle which is set by the calibration period selection bits.
Table 10 shows the how to distinguish “H” period of each clock
signal.
(2) How to invalidate interrupt after prohibition setup of current in-
tegrator
After changing current integration to prohibition, wait for about
61.0 ms, and then set the request flag to “0”.
(3) How to check truth of interrupt request
Check the current integrate enable bit during the current integra-
tor interrupt routine. When disabling the current integrator, skip
the interrupt processing.
Notes on AD conversion connection mode
When the AD conversion of the current integrator is performed,
do not execute other AD conversion.
When using the AD conversion connection mode at the time of
calibration completion, do not set the AD conversion connection
bit to “1” before calibration starts.
The count value immediately after AD conversion completion of
the current integrator may be incorrect. Only when the count
value immediately after the AD conversion completion, such as
initial proofreading etc, is unnecessary, use the AD conversion
connection mode.
The current integrator starts current integration in the low-speed
clock 1-2 cycles, after setting the current integrate enable bit to
“1”. After setting the current integrate enable bit to “0”, initializa-
tion of 1-2 cycle period of a low-speed clock and an internal
circuit is performed. Do not enable the current integrator again in
this period.
After the current integrate enable bit is set to “1”, current integra-
tion starts with a delay of 1 to 2 cycles of a low-speed clock. As
for the period for 1 to 2 cycle of the low-speed clock immediately
after setting the current integrate enable bit to “0”, the internal cir-
cuit is initialized. Do not enable the current integrator again in this
period.
Table 10 Mode switch timing
Current integrate mode
Calibration mode
12.5 ms setting
15.26 ms setting
31.25 ms setting
62.5 ms setting
Mode switch timing
Period for about 62.5 ms after interrupt occurrence of last integrate period
Period for about 31.25 ms after interrupt occurrence of last integrate period
Period for about 15.625 ms after interrupt occurrence of last integrate period
Period for about 7.8127 ms after interrupt occurrence of last integrate period
相關PDF資料 |
PDF描述 |
|---|---|
| M37532RSS | 8-BIT, 6 MHz, MICROCONTROLLER |
| M37544G2GP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37544M2-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37544M2-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37544M2-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37530T-PTC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 42-pin 1.778mm-pitch SDIP to a 40-pin Narrow-pitch Connector (for 7531, 7540, 7542 and 7544 Groups) |
| M37530T-PTCB | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 40-pin Narrow-pitch Connector to 32-pin 0.8mm-pitch LQFP (for 7531, 7532, 7534, 7540, 7542 and 7544 Groups) |
| M37530T-PTCC | 功能描述:DEV 42-PIN RSS/MCU TO 32-PIN 1.7 RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37531E4FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4FP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MITSUBISHI 8 BIT OTP MCU |
發布緊急采購，3分鐘左右您將得到回復。