- 您現在的位置：買賣IC網 > PDF目錄98005 > M34571G6FP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24 PDF資料下載
參數資料
| 型號： | M34571G6FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| 封裝： | 5.30 X 10.10 MM, 0.80 MM PITCH, PLASTIC, SSOP-24 |
| 文件頁數： | 78/126頁 |
| 文件大?。?/td> | 1776K |
| 代理商： | M34571G6FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
Rev.1.02
May 25, 2007
Page 55 of 124
REJ03B0179-0102
4571 Group
LIST OF PRECAUTIONS
(1) Noise and latch-up prevention
Connect a capacitor on the following condition to prevent noise
and latch-up;
connect a bypass capacitor (approx. 0.1
F) between pins VDD
and VSS at the shortest distance,
equalize its wiring in width and length, and
use relatively thick wire.
Port K is also used as VPP pin. Accordingly, when using this pin,
connect this pin to VSS or VDD. Do not leave this pin open. When
port is used for key matrix, connect it to VDD through a pull-up
resistor.
(2) Note on Power Source Voltage
When the power source voltage value of a microcomputer is less
than the value which is indicated as the recommended operating
conditions, the microcomputer does not operate normally and
may perform unstable operation.
In a system where the power source voltage drops slowly when
the power source voltage drops or the power supply is turned off,
reset a microcomputer when the supply voltage is less than the
recommended operating conditions and design a system not to
cause errors to the system by this unstable operation.
(3) Register initial values 1
The initial value of the following registers are undefined after
system is released from reset. After system is released from reset,
set initial values.
Register Z (2 bits)
Register D (3 bits)
Register E (8 bits)
(4) Register initial values 2
The initial value of the following registers are undefined at RAM
back-up. After system is returned from RAM back-up, set initial
values.
Register Z (2 bits)
Register X (4 bits)
Register Y (4 bits)
Register D (3 bits)
Register E (8 bits)
(5) Program counter
Make sure that the PCH does not specify after the last page of the
built-in ROM.
(6) Stack registers (SKS)
Stack registers (SKs) are eight identical registers, so that
subroutines can be nested up to 8 levels. However, one of stack
registers is used respectively when using an interrupt service
routine and when executing a table reference instruction.
Accordingly, be careful not to over the stack when performing
these operations together.
(7) Multifunction
The input of D4 can be used even when CNTR0 (output) is
selected. The input/output of D4 can be used even when
CNTR0 (input) is selected. Be careful when using inputs of
both CNTR0 and D4 since the input threshold value of CNTR0
pin is different from that of port D4.
“H” output function of port C can be used even when the
CNTR1 (output) is used.
The input/output of P20 can be used even when INT0 is used.
Be careful when using inputs of both INT0 and P20 since the
input threshold value of INT0 pin is different from that of port
P20.
The input/output of P21 can be used even when INT1 is used.
Be careful when using inputs of both INT1 and P21 since the
input threshold value of INT1 pin is different from that of port
P21.
(8) Power-on reset
When the built-in power-on reset circuit is used, set the time for
the supply voltage to rise from 0 V to the minimum voltage of
recommended operating conditions to 100
s or less.
If the rising time exceeds 100
s, connect a capacitor between
the RESET pin and Vss at the shortest distance, and input “L”
level to RESET pin until the value of supply voltage reaches the
minimum operating voltage.
(9) POF instruction
When the POF instruction is executed continuously after the
EPOF instruction, system enters the RAM back-up state.
Note that system cannot enter the RAM back-up state when
executing only the POF instruction.
Be sure to disable interrupts by executing the DI instruction
before executing the EPOF instruction and the POF instruction
continuously.
相關PDF資料 |
PDF描述 |
|---|---|
| M34584EDFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M35047-XXXSP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
| M35047-XXXFP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20 |
| M35048-001FP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20 |
| M35049-XXXFP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34571G6-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34571GD | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34571GDFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34571GD-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M3458 | 功能描述:電纜固定件和配件 RLTCG 3/8 NPT BLACK NO NUT RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
發布緊急采購，3分鐘左右您將得到回復。