參數資料
型號: M34571G6FP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24
封裝: 5.30 X 10.10 MM, 0.80 MM PITCH, PLASTIC, SSOP-24
文件頁數: 66/126頁
文件大小: 1776K
代理商: M34571G6FP
Rev.1.02
May 25, 2007
Page 44 of 124
REJ03B0179-0102
4571 Group
RAM BACK-UP MODE
The 4571 Group has the RAM back-up mode.
When the POF instruction is executed continuously after the
EPOF instruction, system enters the RAM back-up state.
The POF instruction is equal to the NOP instruction when the
EPOF instruction is not executed before the POF instruction.
As oscillation stops retaining RAM, the function of reset circuit
and states at RAM back-up mode, current dissipation can be
reduced without losing the contents of RAM.
Table 19 shows the function and states retained at RAM back-up.
Figure 47 shows the state transition.
(1) Identification of the start condition
Warm start (return from the RAM back-up state) or cold start
(return from the normal reset state) can be identified by
examining the state of the power down flag (P) with the SNZP
instruction.
(2) Warm start condition
When the external wakeup signal is input after the system enters
the RAM back-up state by executing the EPOF instruction and
POF instruction continuously, the CPU starts executing the
program from address 0 in page 0. In this case, the P flag is “1.”
(3) Cold start condition
The CPU starts executing the program from address 0 in page 0
when;
“L” level is applied to RESET pin,
system reset (SRST) is performed,
reset by watchdog timer is performed,
reset by the built-in power-on reset circuit is performed, or
reset by the voltage drop detection circuit is performed.
In this case, the P flag is “0.”
Note 1.“O” represents that the function can be retained, and “
×
represents that the function is initialized.
Registers and flags other than the above are undefined at
RAM back-up, and set an initial value after returning.
Note 2.The stack pointer (SP) points the level of the stack register
and is initialized to “7” at RAM back-up.
Note 3.The state of the timer is undefined.
Note 4.Initialize the watchdog timer flag WDF1 with the WRST
instruction, and then set the system to be in the RAM
back-up mode.
Note 5.The voltage drop detection circuit is invalid.
Note 6.C/CNTR pin outputs “L” level. Other ports retain their
output levels.
Table 19 Functions and states retained at RAM back-up
Function
RAM back-up
Program counter (PC), stack pointer (SP)
(Table 2), carry flag (CY), registers A, B
×
Contents of RAM
O
Interrupt control registers V1, V2
×
Interrupt control registers I1, I2
O
Clock control register MR
×
Timer 1, Timer 2, Timer 3 function
(Note 3)
Watchdog timer function
× (Note 4)
Timer control registers PA, W3
×
Timer control registers W1, W2, W5
O
Voltage drop detection circuit
(Note 5)
Port level
(Note 6)
Key-on wakeup control registers K0 to K2, L1
O
Pull-up control registers PU0 to PU2
O
Port output structure control registers FR0, FR1
O
External interrupt request flags (EXF0, EXF1)
×
Timer interrupt request flags (T1F, T2F, T3F)
(Note 3)
Voltage drop detection circuit interrupt request
flag (VDF)
×
Interrupt enable flag (INTE)
×
Watchdog timer flags (WDF1, WDF2)
× (Note 4)
Watchdog timer enable flag (WEF)
× (Note 4)
相關PDF資料
PDF描述
M34584EDFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42
M35047-XXXSP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20
M35047-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35048-001FP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35049-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
相關代理商/技術參數
參數描述
M34571G6-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571GD 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571GDFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571GD-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3458 功能描述:電纜固定件和配件 RLTCG 3/8 NPT BLACK NO NUT RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: