參數資料
型號： M306N0MCT-XXXXFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
封裝： PLASTIC, QFP-100
文件頁數： 63/158頁
文件大?。?/td> 3298K
代理商： M306N0MCT-XXXXFP
155
CPU Rewrite Mode
Under
development
Tentative Specifications REV.A
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30218 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Microcomputer Mode and Boot Mode
The control program for CPU rewrite mode must be written into the user ROM or boot ROM area in
parallel I/O mode beforehand. (If the control program is written into the boot ROM area, the standard
serial I/O mode becomes unusable.)
See Figure AA-3 for details about the boot ROM area.
Normal microcomputer mode is entered when the microcomputer is reset with pulling CNVSS pin low
(VSS). In this case, the CPU starts operating using the control program in the user ROM area.
When the microcomputer is reset by pulling the P52 pin high (VCC), the CNVSS pin high(VPPH), the CPU
starts operating using the control program in the boot ROM area. This mode is called the “boot” mode.
The control program in the boot ROM area can also be used to rewrite the user ROM area.
CPU rewrite mode operation procedure
The internal flash memory can be operated on to program, read, verify, or erase it while being placed on-
board by writing commands from the CPU to the flash memory control register (addresses 03B416,
03B516) and flash command register (address 03B616). Note that when in CPU rewrite mode, the boot
ROM area cannot be accessed for program, read, verify, or erase operations. Before this can be accom-
plished, a CPU write control program must be written into the boot ROM area in parallel input/output
mode. The following shows a CPU rewrite mode operation procedure.
<Start procedure (Note 1)>
(1) Apply VPPH to the CNVSS/VPP pin and VCC to the port P46 pin for reset release. Or the user can
jump from the user ROM area to the boot ROM area using the JMP instruction and execute the CPU
write control program. In this case, set the CPU write mode select bit of the flash memory control
register to “1” before applying VPPH to the CNVSS/VPP pin.
(2) After transferring the CPU write control program from the boot ROM area to the internal RAM, jump
to this control program in RAM. (The operations described below are controlled by this program.)
(3) Set the CPU rewrite mode select bit to “1”.
(4) Read the CPU rewrite mode monitor flag to see that the CPU rewrite mode is enabled.
(5) Execute operation on the flash memory by writing software commands to the flash command regis-
ter.
Note 1: In addition to the above, various other operations need to be performed, such as for entering the
data to be written to flash memory from an external source (e.g., serial I/O), initializing the ports, and
writing to the watchdog timer.
<Clearing procedure>
(1) Apply VSS to the CNVSS/VPP pin.
(2) Set the CPU rewrite mode select bit to “0”.
相關PDF資料
PDF描述
M306N5FCTGP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
M306N5FCFP 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
M306N5FCVFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
M306N5FCVGP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
M306N5MCT-XXXGP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M306N3T-EPB 功能描述:EMULATOR PERSONALITY KIT M16C/6N RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
M306N4FCFP 功能描述:MCU 5V 128K 100-QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/60/6N4 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
M306N4FCFP#UKJ 功能描述:MCU FLASH 128K 5K 100-QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/60/6N4 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
M306N4FCGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Renesas MCU
M306N4FCGP#U3 功能描述:IC M16C MCU FLASH 128K 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/60/6N4 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*