- 您現在的位置：買賣IC網 > PDF目錄4339 > M1AGLE3000V2-FGG896I (Microsemi SoC)IC FPGA 1KB FLASH 3M 896-FBGA PDF資料下載
參數資料
| 型號： | M1AGLE3000V2-FGG896I |
| 廠商： | Microsemi SoC |
| 文件頁數： | 30/166頁 |
| 文件大小： | 0K |
| 描述： | IC FPGA 1KB FLASH 3M 896-FBGA |
| 標準包裝： | 27 |
| 系列： | IGLOOe |
| 邏輯元件/單元數： | 75264 |
| RAM 位總計： | 516096 |
| 輸入/輸出數： | 620 |
| 門數： | 3000000 |
| 電源電壓： | 1.14 V ~ 1.575 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 896-BGA |
| 供應商設備封裝： | 896-FBGA（31x31） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁
Revision 13
3-1
3 – Pin Descriptions and Packaging
Supply Pins
GND
Ground
Ground supply voltage to the core, I/O outputs, and I/O logic.
GNDQ
Ground (quiet)
Quiet ground supply voltage to input buffers of I/O banks. Within the package, the GNDQ plane is
decoupled from the simultaneous switching noise originated from the output buffer ground domain. This
minimizes the noise transfer within the package and improves input signal integrity. GNDQ must always
be connected to GND on the board.
VCC
Core Supply Voltage
Supply voltage to the FPGA core, nominally 1.5 V for IGLOOe V5 devices, and 1.2 V or 1.5 V for
IGLOOe V2 devices. VCC is required for powering the JTAG state machine in addition to VJTAG. Even
when a device is in bypass mode in a JTAG chain of interconnected devices, both VCC and VJTAG must
remain powered to allow JTAG signals to pass through the device.
For IGLOOe V2 devices, VCC can be switched dynamically from 1.2 V to 1.5 V or vice versa. This allows
in-system programming (ISP) when VCC is at 1.5 V and the benefit of low power operation when VCC is
at 1.2 V.
VCCIBx
I/O Supply Voltage
Supply voltage to the bank's I/O output buffers and I/O logic. Bx is the I/O bank number. There are up to
eight I/O banks on IGLOOe devices plus a dedicated VJTAG bank. Each bank can have a separate VCCI
connection. All I/Os in a bank will run off the same VCCIBx supply. VCCI can be 1.2 V, 1.5 V, 1.8 V, 2.5 V,
or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VCCI pins tied to GND.
VMVx
I/O Supply Voltage (quiet)
Quiet supply voltage to the input buffers of each I/O bank. x is the bank number. Within the package, the
VMV plane biases the input stage of the I/Os in the I/O banks. This minimizes the noise transfer within
the package and improves input signal integrity. Each bank must have at least one VMV connection, and
no VMV should be left unconnected. All I/Os in a bank run off the same VMVx supply. VMV is used to
provide a quiet supply voltage to the input buffers of each I/O bank. VMVx can be 1.2 V, 1.5 V, 1.8 V,
2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VMV pins tied to GND.
VMV and VCCI should be at the same voltage within a given I/O bank. Used VMV pins must be
connected to the corresponding VCCI pins of the same bank (i.e., VMV0 to VCCIB0, VMV1 to VCCIB1,
etc.).
VCCPLA/B/C/D/E/F
PLL Supply Voltage
Supply voltage to analog PLL, nominally 1.5 V or 1.2 V, depending on the device.
1.5 V for IGLOOe devices
1.2 V or 1.5 V for IGLOOe V2 devices
When the PLLs are not used, the place-and-route tool automatically disables the unused PLLs to lower
power consumption. The user should tie unused VCCPLx and VCOMPLx pins to ground. Microsemi
recommends tying VCCPLx to VCC and using proper filtering circuits to decouple VCC noise from the
PLLs. Refer to the PLL Power Supply Decoupling section in the "Clock Conditioning Circuits in Low
Power Flash FPGAs and Mixed Signal FPGAs" chapter in the IGLOOe FPGA Fabric User’s Guide for a
complete board solution for the PLL analog power supply and ground.
There are six VCCPLX pins on IGLOOe devices.
相關PDF資料 |
PDF描述 |
|---|---|
| 24LC024T-I/SN | IC EEPROM 2KBIT 400KHZ 8SOIC |
| APA1000-PQG208I | IC FPGA PROASIC+ 1M 208-PQFP |
| 24LC024-I/SN | IC EEPROM 2KBIT 400KHZ 8SOIC |
| APA1000-PQ208I | IC FPGA PROASIC+ 1M 208-PQFP |
| 24C02CT/SN | IC EEPROM 2KBIT 400KHZ 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M1AGLE3000V2-FGG896PP | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOOe Low-Power Flash FPGAs with Flash Freeze Technology |
| M1AGLE3000V5-FFG484 | 制造商:Microsemi Corporation 功能描述:FPGA IGLOOE 3M GATES 130NM 1.5V 484FBGA - Trays |
| M1AGLE3000V5-FFG896 | 制造商:Microsemi Corporation 功能描述:FPGA IGLOOE 3M GATES 130NM 1.5V 896FBGA - Trays |
| M1AGLE3000V5-FFG896ES | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOOe Low-Power Flash FPGAs with Flash Freeze Technology |
| M1AGLE3000V5-FFG896I | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOOe Low-Power Flash FPGAs with Flash Freeze Technology |
發布緊急采購，3分鐘左右您將得到回復。