- 您現在的位置：買賣IC網 > PDF目錄369885 > LXT360PE PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC PDF資料下載
參數資料
| 型號： | LXT360PE |
| 英文描述： | PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC |
| 中文描述： | 的PCM收發器|單|優稅PCM-30/E-1 |的CMOS | LDCC | 28腳|塑料 |
| 文件頁數： | 30/52頁 |
| 文件大小： | 1187K |
| 代理商： | LXT360PE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
LXT361
—
Integrated T1/E1 LH/SH Transceiver for DS1/DSX-1 or PRI Applications
30
Datasheet
Table 13. Performance Status Register
Read Only, Address (A7-A0) = x010101x
Bit
Name
Function
0
LOS
1 = Loss of Signal occurred.
0 = Loss of Signal did not occur.
1
NLOOP
1 = Network loopback active.
0 = Network loopback not active.
2
AIS
1 = Alarm Indicator Signal detected.
0 = Alarm Indicator Signal not detected.
3
QRSS
1 = Quasi-Random Signal Source pattern detected.
0 = Quasi-Random Signal Source pattern not detected.
4
-
reserved
–
ignore.
5
DFMO
1 = Driver Failure Monitor Open detected.
0 = Driver Failure Monitor Open not detected.
6
BIST
1 = Built-In Self Test passed.
0 = Built-In Self Test did not pass (or was not run).
7
-
reserved
–
ignore.
Table 14. Equalizer Status Register
Read Only, Address (A7-A0) = x010110x
Bit
Name
Function
0
-
reserved
–
ignore (Least Significant Bit)
1
-
reserved
–
ignore
2
-
reserved
–
ignore
3
-
reserved
–
ignore
4
LATN4
Receive Line Attenuation Indicators. Convert this binary output to a decimal number and multiply
by 2.9 dB to determine the approximate cable attenuation as seen by the receiver.
For example, if LATN7-4 = 1010
(= 10
), then the receiver is seeing a signal attenuated by
approximately 29 dB (2.9 dB
x
10) of cable. This approximation assumes that a 3 V pulse was
transmitted.
5
LATN5
6
LATN6
7
LATN7
Table 15. Control Register #4
Read/Write,
Address (A7-A0) = x010111x
Bit
Name
Function
0
CODEV
1 = Enable detection of HDB3 code violations at the BPV pin along with bipolar violations and Zero
Substitution Violations (if enabled).
0 = Disable detection of HDB3 code violations
1
ZEROV
1 = Enable detection of HDB3 Zero Substitution Violations (four consecutive zeros). Note that Zero
Substitution Violations are reported at the BPV pin.
0 = Disable detection of HDB3 Zero Substitution Violations.
2
LOS2048
1 = Set LOS detection threshold to 2048 consecutive zeros.
0 = Set LOS detection threshold to 32 consecutive zeros (for E1 operation) or to 175 consecutive
zeros (for T1 operation).
3
COL32CM
1 = Set LOS clear condition criterion to receipt of 32 consecutive marks (E1 operation).
0 = Set LOS clear condition criterion to 12.5% mark density (E1 operation).
相關PDF資料 |
PDF描述 |
|---|---|
| LXT384BE | Telecomm/Datacomm |
| LXT384LE | Telecomm/Datacomm |
| LXT386BE | PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|BGA|160PIN|PLASTIC |
| LXT386LE | PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC |
| LXT388LE | PCM TRANSCEIVER|DUAL|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT360QE | 制造商:Intel 功能描述: 制造商:LEVEL ONE 功能描述: |
| LXT361 | 制造商:LVL1 制造商全稱:LVL1 功能描述:Integrated T1/E1 LH/SH Transceivers for DS1/DSX-1/CSU or NTU/ISDN PRI Applications |
| LXT361LE | 制造商:LEVEL ONE 功能描述:361LE |
| LXT361PE | 制造商:LEVEL 1 功能描述: 制造商:LEVEL ONE 功能描述: 制造商:Intel 功能描述:PCM TRANSCEIVER, Single, CEPT PCM-30/E-1, 28 Pin, Plastic, PLCC |
| LXT361QE | 制造商:LEVEL ONE 功能描述: 制造商:LEVEL ONE 功能描述:DATACOM, PCM TRANSCEIVER, PQFP44 |
發布緊急采購，3分鐘左右您將得到回復。