參數資料
型號: LXT360PE
英文描述: PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC
中文描述: 的PCM收發器|單|優稅PCM-30/E-1 |的CMOS | LDCC | 28腳|塑料
文件頁數: 22/52頁
文件大?。?/td> 1187K
代理商: LXT360PE
LXT361
Integrated T1/E1 LH/SH Transceiver for DS1/DSX-1 or PRI Applications
22
Datasheet
3.5.3
Error Insertion and Detection
3.5.3.1
Bipolar Violation Insertion
(INSBPV)
Bipolar violation insertion is available In Unipolar mode. Choosing Unipolar mode configures the
INSBPV pin. To insert bipolar violation (BPV), a Low-to-High transition on the INSBPV is
required. Sampling occurs on the falling edge of TCLK. When INSBPV goes High a BPV is
inserted on the next available mark except in the four following situations:
Zero suppression (HDB3 or B8ZS) is not violated
If LLOOP and TAOS are both active, the BPV is looped back to RNEG/BPV indicator and the
line driver transmits all ones with no violation
BPV insertion is disabled with RLOOP active
BPV insertion is disabled when NLOOP is active
With the LXT361 configured to transmit internally generated data patterns (QRSS or NLOOP), a
BPV can be inserted into the transmit pattern regardless of whether the device is in the Unipolar or
Bipolar mode of operation.
3.5.3.2
Logic Error Insertion
(INSLER)
When configured to transmit internally generated data patterns (QRSS or NLOOP Up/Down
codes), a logic error is inserted into the transmit data pattern when the INSLER pin transitions
Low-to-High. Note that in QRSS mode, there is no logic error insertion on a jammed bit (i.e., a bit
forced to one to suppress transmission of more than 14 consecutive zeros). The transceiver routes
data patterns the same way it routes data applied to TPOS/TNEG. Therefore, the inserted logic
error will follow the data flow path of the active loopback mode.
3.5.3.3
Bipolar Violation Detection
(BPV)
When the internal encoders/decoders are disabled or when configured in Unipolar mode, bipolar
violations are reported at the BPV pin. BPV goes High for a full clock cycle to indicate receipt of a
BPV. When the encoders/decoders are enabled, the LXT361 does not report bipolar violations due
to the line coding scheme.
3.5.3.4
HDB3 Code Violation Detection
(CODEV)
An HDB3 code violation (CODEV) occurs when two consecutive bipolar violations of the same
polarity are received (refer to ITU O.161). When CODEV detection is enabled, the BPV pin goes
High for a full RCLK cycle to report a CODEV violation. Note that bipolar violations and zero
substitution violations will also be reported on the BPV pin if these options are enabled.
HDB3 code violation detection is enabled when the HDB3 encoders/decoders are enabled. This
requires that CR1.ENCENB = 1, also CR1.EC4:1 = 100x or 1010, which establishes E1 operation.
To select CODEV detection, set bit CR4.CODEV = 1.
3.5.3.5
HDB3 Zero Substitution Violation Detection
(ZEROV)
An HDB3 ZEROV is the receipt of four or more consecutive zeros. This does not occur with
correctly encoded HDB3 data unless there are transmission errors. The BPV pin goes High for a
full RCLK cycle to report a ZEROV. Note that when ZEROV detection enabled, the BPV pin will
also indicate received BPVs and CODEVs, if these detection options are enabled.
相關PDF資料
PDF描述
LXT384BE Telecomm/Datacomm
LXT384LE Telecomm/Datacomm
LXT386BE PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|BGA|160PIN|PLASTIC
LXT386LE PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC
LXT388LE PCM TRANSCEIVER|DUAL|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC
相關代理商/技術參數
參數描述
LXT360QE 制造商:Intel 功能描述: 制造商:LEVEL ONE 功能描述:
LXT361 制造商:LVL1 制造商全稱:LVL1 功能描述:Integrated T1/E1 LH/SH Transceivers for DS1/DSX-1/CSU or NTU/ISDN PRI Applications
LXT361LE 制造商:LEVEL ONE 功能描述:361LE
LXT361PE 制造商:LEVEL 1 功能描述: 制造商:LEVEL ONE 功能描述: 制造商:Intel 功能描述:PCM TRANSCEIVER, Single, CEPT PCM-30/E-1, 28 Pin, Plastic, PLCC
LXT361QE 制造商:LEVEL ONE 功能描述: 制造商:LEVEL ONE 功能描述:DATACOM, PCM TRANSCEIVER, PQFP44