- 您現在的位置：買賣IC網 > PDF目錄369872 > LU3X54FTL-HS208-DB QUAD-FET for 10Base-T/100Base-TX/FX PDF資料下載
參數資料
| 型號： | LU3X54FTL-HS208-DB |
| 英文描述： | QUAD-FET for 10Base-T/100Base-TX/FX |
| 中文描述： | 四核10Base-T/100Base-TX/FX場效應管 |
| 文件頁數： | 38/54頁 |
| 文件大?。?/td> | 677K |
| 代理商： | LU3X54FTL-HS208-DB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
LU3X54FT
QUAD-FET for 10Base-T/100Base-TX/FX
Data Sheet
July 2000
38
Lucent Technologies Inc.
MII Station Management
(continued)
Management Registers (MR)
(continued)
Table 21. MR30—Device-Specific Register 3 (10 Mbits/s Control) Bit Descriptions
1. Note that the format for the bit descriptions is as follows: the first number is the register number, the second number is the bit position in the
register, and the name of the instantiated pad is in capital letters.
2 R = read, W = write.
Register/Bit
1
30.15:7 (R28[15:7])
30.6 (CLK_SEL)
Type
2
R/W
R/W
Description
Unused.
Read as 0.
20 MHz Clock Select
.
When this bit is a 1, it enables the two-clock input mode
(20 MHz and 25 MHz). When this bit is a 0, it enables the single-clock input
mode (25 MHz with 20 MHz clock internally generated). Default state is 0
.
Heartbeat Enable.
When this bit is a 1, the heartbeat function will be
enabled. Valid in 10 Mbits/s mode only. Default state is 0.
Extended Line Length Enable.
When this bit is a 1, the receive squelch lev-
els are reduced from a nominal 435 mV to 350 mV, allowing reception of sig-
nals with a lower amplitude. Valid in 10 Mbits/s mode only. Default state is 0.
Autopolarity Function Disable.
When this bit is a 0 and the LU3X54FT is in
10 Mbits/s mode, the autopolarity function will determine if the TP link is wired
with a polarity reversal.
30.5 (HBT_EN)
R/W
30.4 (ELL_EN)
R/W
30.3 (APF_DIS)
R/W
If there is a polarity reversal, the LU3X54FT will assert the APS bit (register
28, bit 6) and correct the polarity reversal. If this bit is a 1 and the device is in
10 Mbits/s mode, the reversal will not be corrected. Default state is 0.
Reference Select.
When this bit is a 1, the external 10 MHz reference input
clock REF10 is used for phase alignment. Default state is 0.
Serial Select.
When this bit is set to a 1, 10 Mbits/s serial mode will be
selected. When the LU3X54FT is in 100 Mbits/s mode, this bit will be ignored.
This bit is ORed with the H_DUPLED[C] pin during powerup and reset.
Default state is 0.
No Link Pulse Mode.
Setting this bit to a 1 will allow 10 Mbits/s operation
with link pulses disabled. If the LU3X54FT is configured for 100 Mbits/s opera-
tion, setting this bit will not affect operation. This bit is ORed with the
LINKLED[A] pin during powerup and reset. Default state is 0.
30.2 (REF_SEL)
R/W
30.1 (SERIAL _SEL)
R/W
30.0 (ENA_NO_LP)
R/W
相關PDF資料 |
PDF描述 |
|---|---|
| LU3X54FT | Quad-FET (Fast Ethernet Transceiver) for 10Base-T/100Base-TX/FX(應用于10基數-T和100基數-TX/FX的四快速以太網收發器) |
| LU5X34F | Quad Gigabit Ethernet Transceiver |
| LU5X34F | Quad Gigabit Ethernet Transceiver(千兆位以太網四收發器) |
| LUCL8551AAU | Subscriber Line Interface Circuit |
| LUCL8551AP | Subscriber Line Interface Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LU3X54FTLHS208-DB | 制造商:Alcatel-Lucent 功能描述:3X54FTLHS208-DB |
| LU400 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:NEMA Cabinet Legs |
| LU400/D | 制造商:OSRAM 功能描述:400W MOGUL BASED GENERAL LIGHTING HIGH PRESSURE SODIUM LAMP, COATED, DAYLIGHT, U |
| LU400/PLUS/ECO | 制造商:OSRAM 功能描述:400W NON CYCLING, ENVIRONMENTALLY FRIENDLIER HIGH PRESSURE SODIUM LAMP, CLEAR, U |
| LU47 | 制造商:Thomas & Betts 功能描述:1-1/4 CONDUIT BODY,IRON,LU,F-7 |
發布緊急采購，3分鐘左右您將得到回復。