- 您現在的位置：買賣IC網 > PDF目錄369872 > LU3X54FTL-HS208-DB QUAD-FET for 10Base-T/100Base-TX/FX PDF資料下載
參數資料
| 型號： | LU3X54FTL-HS208-DB |
| 英文描述： | QUAD-FET for 10Base-T/100Base-TX/FX |
| 中文描述： | 四核10Base-T/100Base-TX/FX場效應管 |
| 文件頁數： | 25/54頁 |
| 文件大?。?/td> | 677K |
| 代理商： | LU3X54FTL-HS208-DB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Lucent Technologies Inc.
25
Data Sheet
July 2000
LU3X54FT
QUAD-FET for 10Base-T/100Base-TX/FX
171—168
RXLED[D:A]/
FX_MODE_EN[D:A]
I/O
Receive LED[D:A].
This pin indicates receive activity. External buffers
are necessary to drive the LEDs.
FX Mode Enable.
At powerup or reset,
when pulled high through a
4.7 k
resistor, this pin will enable the FX mode (10Base-T and
100Base-TX disabled). When pulled low, it will enable 10Base-T and
100Base-TX modes (100Base-FX mode disabled). These pins are
ORed with register 29, bit 0 [29.0].
These pins have internal 50 k
pull-down resistors.
Collision LED.
This pin indicates collision occurrence. External buffers
are necessary to drive the LEDs.
176—173
COLED[D:A]
O
Channels A and B have internal 50 k
pull-down resistors but not
channels C and D.
Link LED[D]
. This pin indicates good link status on port D. External
buffers are necessary to drive the LEDs.
PHY Address 2.
At powerup or reset, this pin is used to set the PHY
address bit 2.
190
LINKLED[D]/
PHYADD[2]
I/O
If this pin is pulled high through a 50 k
resistor, it will set PHYADD[2]
to a 1. If this pin is pulled low through a 50 k
resistor, it will set
PHYADD[2] to a 0.
Link LED[C].
This pin indicates good link status on port C. External
buffers are necessary to drive the LEDs.
PHY Address 1.
At powerup or reset, this pin is used to set the PHY
address bit 1.
189
LINKLED[C]/
PHYADD[1]
I/O
If this pin is pulled high through a 50 k
resistor, it will set PHYADD[1]
to a 1. If this pin is pulled low through a 50 k
resistor, it will set
PHYADD[1] to a 0.
Link LED[B].
This pin indicates good link status on port B. External
buffers are necessary to drive the LEDs.
PHY Address 0.
At powerup or reset, this pin may be used to set the
PHY address bit 0.
188
LINKLED[B]/
PHYADD[0]
I/O
If this pin is pulled high through a 50 k
resistor, it will set PHYADD[0]
to a 1. If this pin is pulled low through a 50 k
resistor, it will set
PHYADD[0] to a 0.
Link LED[A].
This pin indicates good link status on port A. External
buffers are necessary to drive the LEDs.
No Link Pulse.
This pin is used at powerup or reset to select the
NO_LP function of register 30, bit 0 for all four channels by pulling this
pin high through a 4.7 k
resistor. This input and the register bit [30.0]
are ORed together.
187
LINKLED[A]/
NO_LP
I/O
This pin has an internal 50 k
pull-down resistor to set the default to
normal link pulse ON mode.
Pin Information
(continued)
Pin Descriptions
(continued)
Table 7. Miscellaneous Pins
(continued)
Pin
Signal
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| LU3X54FT | Quad-FET (Fast Ethernet Transceiver) for 10Base-T/100Base-TX/FX(應用于10基數-T和100基數-TX/FX的四快速以太網收發器) |
| LU5X34F | Quad Gigabit Ethernet Transceiver |
| LU5X34F | Quad Gigabit Ethernet Transceiver(千兆位以太網四收發器) |
| LUCL8551AAU | Subscriber Line Interface Circuit |
| LUCL8551AP | Subscriber Line Interface Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LU3X54FTLHS208-DB | 制造商:Alcatel-Lucent 功能描述:3X54FTLHS208-DB |
| LU400 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:NEMA Cabinet Legs |
| LU400/D | 制造商:OSRAM 功能描述:400W MOGUL BASED GENERAL LIGHTING HIGH PRESSURE SODIUM LAMP, COATED, DAYLIGHT, U |
| LU400/PLUS/ECO | 制造商:OSRAM 功能描述:400W NON CYCLING, ENVIRONMENTALLY FRIENDLIER HIGH PRESSURE SODIUM LAMP, CLEAR, U |
| LU47 | 制造商:Thomas & Betts 功能描述:1-1/4 CONDUIT BODY,IRON,LU,F-7 |
發布緊急采購，3分鐘左右您將得到回復。