- 您現在的位置：買賣IC網 > PDF目錄361035 > LM9832CCVJD (NATIONAL SEMICONDUCTOR CORP) LM9832 42-Bit Color, 1200dpi USB Image Scanner PDF資料下載
參數資料
| 型號： | LM9832CCVJD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | PLASTIC, TQFP-100 |
| 文件頁數： | 35/42頁 |
| 文件大?。?/td> | 337K |
| 代理商： | LM9832CCVJD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
35
www.national.com
12.4 - Acceleration Profile Modified
The highest setting of the Acceleration Profile (bits 2-7 of register
51) has been modified to give the motor more time during the
acceleration/deceleration phases. In the LM9831, a setting of 3
for the “stopped” time, “25%” time, and “50%” time caused the
state machine to spend 3 full steps in that state. In the LM9832, a
setting of 3 will cause the state machine to spend 8 full steps in
that state.
12.5 1 Channel Color Mode
When using the LM9831 in 1 Channel Color Mode with the hold
current timeout set to 0, the LM9831 would sometimes skip a line
during a pause/resume cycle. This problem has been fixed in the
LM9832.
12.6 DRAM Control Signals
The RD, WR, CAS, and RAS pins are now tri-stated when the
LM9832 is in Suspend Mode. In a USB bus-powered application
where the DRAM is powered down in suspend mode but the
LM9832’s VDRAM supply still has power, this change prevents
the RD, WR, CAS, and RAS pins from potentially forward biasing
the input protection diodes of the external DRAM which could
cause the current drawn from the USB’s power source to exceed
the 2.5mA maximum allowable current draw when in suspend
mode.
12.7 Start of Scan Reset
In the LM9831, the value in register 01 is not reset (and therefore
not accurate) until the first line of the image has been scanned.
The LM9832 resets this counter as soon as a scan is initiated, so
the value in register 01 is always valid.
12.8 Power-On Reset (POR)
The LM9831 has a power-on reset circuit that causes the chip to
be reset during power-up when the analog power supply (V
A
)
passes 2V. If V
A
ramped very slowly (2V/ms), this could cause
the LM9831 to be reset and start trying to load data from the
external EEPROM before the external was EEPROM became
active, which could cause the LM9831 to think there was no
external EEPROM attached.
The LM9832 has a power-on reset threshold to 3V, to reduce the
chance of this occurring. Additionally, the input to the POR comes
from V
D
, not V
A
. This allows the V
A
supply to be switched off
when in Suspend mode, allowing more flexibility in USB bus-pow-
ered designs.
12.9 Remote Wakeup
The LM9832 supports enabling and disabling remote wakeup
through the LM9832 minidriver software.
12.10 Reduced Current Consumption
The LM9832 includes 4 current settings (100%, 80%, 70%, and
50%) to control the current consumed by the analog supply (V
A
).
The LM9832 is tested and guaranteed at the 100% setting, which
is the same as the LM9831’s analog section. For USB bus-pow-
ered settings, To reduce the current consumption (for bus-pow-
ered applications) set this register to one of the 3 other settings.
The performance of the analog section (INL, DNL, and noise) will
degrade at the lower settings, but this may not be noticeable in
the final image, particularly with CIS sensors where the noise and
non-linearities of the sensor may be far greater than that of the
LM9832’s analog front end.
12.11 Motor Phase Swap
Bit 5 has been added to register 45 to “swap” the A and B stepper
motor phases. This will reverse the stepper motor’s direction of
movement. This can be used to make the scanner scan in the
opposite (or both) directions, provides an alternative means of
sensing the home position by scanning towards home until a pat-
tern on the calibration strip (instead of an optical sensor) is
detected, and also provides a software fix for a motor that hap-
pens to be wired backwards. Note that this only works in fullstep
mode.
12.12 ITA Output on LAMP
B
The LM9832 adds 1 bit (register 29 bit 2) that, when set, will out-
put the ITA (Integration Time Adjust) phase on the LAMP
B
output
pin. This signal can potentially be used to turn off the illumination
source during the ITA’s long integration time period.
12.13 Faster Fullstep Movement
In Fullstep Mode, the LM9831 and LM9832 normally move the
motor with the motor winding current set to 0.35V/R
SENSE
(0.5V/R
SENSE
during the Kickstart period at the start of move-
ment). The problem is that the ideal R
SENSE
value for microstep-
ping was too small for fullstepping, and vice-versa. So if the
scanner needed to use both modes (fullstepping for high speed
movement and low resolution scans, microstepping for high reso-
lution scans), there wasn’t a sense resistor value that worked well
for both.
The LM9832 improves this situation by adding this function: if the
Kickstart Steps value (register 55 bits 0-2) is set to 0, the LM9832
will set the winding current to 0.5V/R
SENSE
for all fullstep move-
ment. This provides more current to the stepper motor in fullstep
mode, while allowing the sense resistor to be at a value optimized
for microstepping.
12.14 Fullstepping Fastfeed, Microstepping Scan
The LM9832 adds 1 bit (register 45 bit 6) that, when set, makes
the scanner automatically use fullstep mode for fastfeeding at the
start of scan, then switch to microstepping when scan begins.
12.15 Device and Vendor IDs for USB Interface
The LM9832’s internal (default) ROM is programmed for a Ven-
dor ID of 0x0400 and Device ID of 0x0001. The Vendor String is
“National Semiconductor” and the Device String is “LM9832 42
Bit Scanner”.
12.16 Paper Sensor #2 Doesn’t Stop High Speed Reverse
In the LM9831, a false-to-true transition on Paper Sensor #2
would stop a high speed reverse (usually used for homing in flat-
bed scanners). Due to the changes made to accommodate the
FullStep Timeout Function
function, the ability to stop a high
speed reverse function was removed.
Applications Information
(Continued)
L
相關PDF資料 |
PDF描述 |
|---|---|
| LM9832 | LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| LM9833CCVJD | LM9833 48-Bit Color, 1200dpi USB Image Scanner |
| LM9833 | LM9833 48-Bit Color, 1200dpi USB Image Scanner |
| LM98501CCVBH | 10-Bit, 27 MSPS Camera Signal Processor |
| LM98501 | 10-Bit, 27 MSPS Camera Signal Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9832CCVS-B | 制造商:Texas Instruments 功能描述: |
| LM9833 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9833 48-Bit Color, 1200dpi USB Image Scanner |
| LM9833B-F WAF | 制造商:Texas Instruments 功能描述: |
| LM9833CCVJD | 制造商:Texas Instruments 功能描述:USB Image Scanner 100-Pin TQFP |
| LM9833CCVJD NOPB | 制造商:Texas Instruments 功能描述:Bulk |
發布緊急采購，3分鐘左右您將得到回復。