- 您現在的位置：買賣IC網 > PDF目錄67755 > LC5521D 2.5 A POWER FACTOR CONTROLLER, 18 kHz SWITCHING FREQ-MAX, DIP7 PDF資料下載
參數資料
| 型號： | LC5521D |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.5 A POWER FACTOR CONTROLLER, 18 kHz SWITCHING FREQ-MAX, DIP7 |
| 封裝： | DIP-8/7 |
| 文件頁數： | 11/40頁 |
| 文件大?。?/td> | 888K |
| 代理商： | LC5521D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
19
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
28106.02
Figure 17. Averaged input current waveform, LC552xD and LC552xF series
FB pin voltage
S/GND
EIN
Drain current
Averaged input current
D/ST
VCC
S/GND
D
V
P
C2
2(4)
8(1)
C4
1(2)
D
L2
LC55xxD
(LC552xF)
D5
R1
VCC
= 3.7mA
ICC(ON) (max)
Sto
p
St
ar
tu
p
ICC
9.4 V
VCC(OFF)
VCC(ON)
15.1 V
Figure 18. VCC pin peripheral circuit
Figure 19. VCC versus operation current, ICC
Startup Operation
Figure 18 shows the VCC pin peripheral circuit. The integrated
startup circuit is connected to the D/ST pin, and it generates a
constant current, ICC(STARTUP) = –3.0 mA, to charge capacitor C4
at the VCC pin. During this process, when VCC voltage reaches
VCC(ON) = 15.1 V, the IC starts operation, and when its voltage
exceeds VCC(BIAS)2 = 16.6 V, the startup circuit stops, in order to
eliminate its own power consumption.
The startup time is determined by the C4 capacitance and is
expressed by the formula below:
tSTART
C4
≈
|ICC(STARTUP)|
VCC(ON) – VCC(INIT)
(1)
where
tSTART is the startup time (s), and
VCC(INIT) is the VCC pin initial voltage (V).
A ceramic or film capacitor can be used for C4, and a value of
0.22 to 22 μF is generally recommended.
Figure 19 shows the relationship between VCC voltage and the
operating current, ICC. When VCC voltage reaches VCC(ON) =
15.1 V, the Controller circuit operation begins and the operating
current increases. After that, if VCC voltage decreases to VCC(OFF)
= 9.4 V, the Undervoltage Lockout (UVLO) circuit stops Control-
ler circuit operation, and the operation state returns to the startup
phase.
After the control circuit starts up, the auxiliary winding (D in
figure 18) voltage, rectified by diode D5, powers the VCC pin.
VCC voltage must satisfy these conditions:
VCC(BIAS)1(max) = 12.5 V < VCC < VCC(OVP)(min) = 28.5 V
相關PDF資料 |
PDF描述 |
|---|---|
| LC72137 | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDIP22 |
| LC72137M | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDSO20 |
| LC72137 | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDIP22 |
| LC72137M | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDSO20 |
| LC99403 | SPECIALTY ANALOG CIRCUIT, BGA180 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC5523D | 制造商:Sanken Electric Co Ltd 功能描述:IC LED DRIVER ISO FLYBACK 8DIP |
| LC5523F | 制造商:Sanken Electric Co Ltd 功能描述:IC LED DVR ISO FLYBACK TO220-7 制造商:ALLEGRO 功能描述:LED Lighting Driver IC, Isolated 制造商:Allegro MicroSystems LLC 功能描述:LED Lighting Driver IC, Isolated |
| LC5525F | 制造商:Sanken Electric Co Ltd 功能描述:IC LED DVR ISO FLYBACK TO220-7 |
| LC552DIP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LC552SOIC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。