- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8993FL (Micrel Inc)IC CONV MED 10/100 SGL 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8993FL |
| 廠商： | Micrel Inc |
| 文件頁數： | 20/100頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONV MED 10/100 SGL 128PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 其它名稱： | 576-1035 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
Micrel, Inc.
KS8993F/FL
June 2009
26
M9999-062509
hbwhelp@micrel.com or (408) 955-1690
For 100BASE-FX operation, the KS8993F FXSD1 (fiber signal detect) input pin is usually connected to the fiber
transceiver SD (signal detect) output pin. 100BASE-FX mode is activated when FXSD1 is greater than 1V. When
FXSD1 is between 1V and 1.8V, no fiber signal is detected and a Far-End Fault is generated if the feature is enabled.
Alternatively, FXSD1 can be tied high to force 100BASE-FX mode if the Far-End Fault feature is not used. When
FXSD1 is greater than 2.2V, the fiber signal is detected.
100BASE-FX signal detection is summarized in the following table.
Table 1: FX and TX Mode Selection
FXSD1 (pin 44)
Condition
Less than 0.2V
TX mode
Greater than 1V, but less than 1.8V
FX mode
No signal detected;
Far-End Fault generated (if enabled)
Greater than 2.2V
FX mode
Signal detected
To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver SD output
voltage swing to match the KS8993F FXSD1 input voltage threshold. Refer to KS8993F schematic for recommended
fiber transceiver connections.
2.3.6
100BASE-FX Far-End Fault (FEF)
Far-End Fault (FEF) occurs when the signal detection is logically false on the receive side of the fiber transceiver. The
KS8993F detects a FEF when its FXSD1 input is between 1.0V and 1.8V. When a FEF occurs, the transmission side
signals the link partner by sending 84 ones followed by 1 zero in the idle period between frames.
Upon receiving a FEF, the link will go down (even when the fiber signal is detected) to indicate a fault condition. The
transmitting side is not affected when a FEF is received, and will continue to send out its normal transmit pattern from
the MAC.
By default, FEF is enabled. FEF can be disabled through register setting.
2.3.7
10BASE-T Transmit and Receive
The output 10BASE-T driver is incorporated into the 100BASE-TX driver to allow transmission with the same magnetic.
They are internally wave-shaped and pre-emphasized into outputs with a typical 2.3 V amplitude.
The harmonic
contents are at least 27 dB below the fundamental when driven by an all-ones Manchester-encoded signal.
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit
and a PLL perform the decoding function. The Manchester-encoded data stream is separated into clock signal and
NRZ data. A squelch circuit rejects signals with levels less than 400 mV or with short pulse widths in order to prevent
noises at the RXP or RXM input from falsely triggering the decoder. When the input exceeds the squelch limit, the PLL
locks onto the incoming signal and the KS8993F decodes a data frame. The receiver clock is maintained active during
idle periods in between data reception.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
| KSZ8995FQ | IC SWITCH 10/100 5PORT 128-PQFP |
| KSZ8995MA | IC SWITCH 10/100 5PORT 128PQFP |
| KSZ8995MI | IC SWITCH 5-PORT 10/100 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8993FL-EVAL | 功能描述:BOARD EVALUATION FOR KSZ8993FL RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| KSZ8993I | 功能描述:以太網 IC 3 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-PQFP, I-TEMP RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993M | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993MA5 | 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8993M-EVAL | 功能描述:以太網開發工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。