- 您現在的位置：買賣IC網 > PDF目錄11575 > KSZ8862-16MQL-FX (Micrel Inc)IC SWITCH ETH 2P 16BIT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8862-16MQL-FX |
| 廠商： | Micrel Inc |
| 文件頁數： | 66/125頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH ETH 2P 16BIT 128PQFP |
| 標準包裝： | 66 |
| 系列： | KSZ8862 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | PCI |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-1638-ND - BOARD EVALUATION KSZ8862-10FL 576-1637-ND - BOARD EVALUATION KSZ8862-100FX |
| 其它名稱： | 576-3271 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
45
M9999-040407-3.0
For ingress rate limiting, KSZ8862M provides options to selectively choose frames from all types, multicast, broadcast,
and flooded unicast frames. The KSZ8862M counts the data rate from those selected type of frames. Packets are
dropped at the ingress port when the data rate exceeds the specified rate limit.
For egress rate limiting, the Leaky Bucket algorithm is applied to each output priority queue for shaping output traffic. Inter
frame gap is stretched on a per frame base to generate smooth, non-burst egress traffic. The throughput of each output
priority queue is limited by the egress rate specified.
If any egress queue receives more traffic than the specified egress rate throughput, packets may be accumulated in the
output queue and packet memory. After the memory of the queue or the port is used up, packet dropping or flow control
will be triggered. As a result of congestion, the actual egress rate may be dominated by flow control/dropping at the
ingress end, and may be therefore slightly less than the specified egress rate.
To reduce congestion, it is good practice to make sure the egress bandwidth exceeds the ingress bandwidth.
MAC Filtering Function
Use the static table to assign a dedicated MAC address to a specific port. When a unicast MAC address is not recorded in
the static table, it is also not learned in the dynamic MAC table. The KSZ8862M includes an option that can filter or
forward unicast packets for an unknown MAC address. This option is enabled by SGCR7 [7].
The unicast MAC address filtering function is useful in preventing the broadcast of unicast packets that could degrade the
quality of this port in applications such as voice over Internet Protocol (VoIP).
Configuration Interface
The KSZ8862M operates only as a managed switch.
EEPROM Interface
It is optional in the KSZ8862M to use an external EEPROM. In the case that an EEPROM is not used, the EEEN pin must
be tied Low or floating.
The external serial EEPROM with a standard microwire bus interface is used for non-volatile storage of information such
as the host MAC address, base address, and default configuration settings. The KSZ8862M can detect if the EEPROM is
a 1KB (93C46) or 4KB (93C66) EEPROM device (the 93C46 and the 93C66 are typical EEPROM devices). The
EEPROM is organized as 16-bit mode.
If the EEEN pin is pulled high, the KSZ8862M performs an automatic read of the external EEPROM words 0H to 6H after
the de-assertion of Reset. The EEPROM values are placed in certain host-accessible registers. EEPROM read/write
functions can also be performed by software read/writes to the EEPCR registers.
The KSZ8862M EEPROM format is given below.
WORD
15
8
7
0
0H
Base Address
1H
Host MAC Address Byte 2
Host MAC Address Byte 1
2H
Host MAC Address Byte 4
Host MAC Address Byte 3
3H
Host MAC Address Byte 6
Host MAC Address Byte 5
4H
Reserved
5H
Reserved
6H
ConfigParam (see Table 13)
7H-3FH
Not used for KSZ8862M (available for user to use)
Table 12. EEPROM Format
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16LF726-E/SO | IC PIC MCU FLASH 8KX14 28-SOIC |
| 0731010340 | BNC JACK VERTICAL PCB 75 OHM |
| V300A5C400BF | CONVERTER MOD DC/DC 5V 400W |
| V300A5C400BL3 | CONVERTER MOD DC/DC 5V 400W |
| PIC16LC620A-04/SS | IC MCU OTP 512X14 COMP 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8862-32MQL | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-32MQL-FX | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-MQL | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support |
| KSZ8863FLL | 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8863FLL-EVAL | 功能描述:以太網開發工具 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。