- 您現在的位置：買賣IC網 > PDF目錄11575 > KSZ8862-16MQL-FX (Micrel Inc)IC SWITCH ETH 2P 16BIT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8862-16MQL-FX |
| 廠商： | Micrel Inc |
| 文件頁數： | 64/125頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH ETH 2P 16BIT 128PQFP |
| 標準包裝： | 66 |
| 系列： | KSZ8862 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | PCI |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-1638-ND - BOARD EVALUATION KSZ8862-10FL 576-1637-ND - BOARD EVALUATION KSZ8862-100FX |
| 其它名稱： | 576-3271 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
43
M9999-040407-3.0
IEEE 802.1Q VLAN Support
The KSZ8862M supports 16 active VLANs out of the 4096 possible VLANs specified in the IEEE 802.1Q specification.
KSZ8862M provides a 16-entry VLAN table, which converts the 12-bits VLAN ID (VID) to the 4-bits Filter ID (FID) for
address lookup. If a non-tagged or null-VID-tagged packet is received, the ingress port default VID is used for lookup. In
VLAN mode, the lookup process starts with VLAN table lookup to determine whether the VID is valid. If the VID is not
valid, the packet is dropped and its address is not learned. If the VID is valid, the FID is retrieved for further lookup. The
FID + Destination Address (FID+DA) are used to determine the destination port. The FID + Source Address (FID+SA) are
used for address learning. (See Tables 10 and 11.)
DA found in
Static MAC
Table?
Use FID flag?
FID match?
DA+FID found in
Dynamic MAC
Table?
Action
No
Don’t care
No
Broadcast to the membership ports
defined in the VLAN Table bits [18:16]
No
Don’t care
Yes
Send to the destination port defined in the
Dynamic MAC Address Table bits [53:52]
Yes
0
Don’t care
Send to the destination port(s) defined in
the Static MAC Address Table bits [50:48]
Yes
1
No
Broadcast to the membership ports
defined in the VLAN Table bits [18:16]
Yes
1
No
Yes
Send to the destination port defined in the
Dynamic MAC Address Table bits [53:52]
Yes
1
Yes
Don’t care
Send to the destination port(s) defined in
the Static MAC Address Table bits [50:48]
Table 10. FID+DA Lookup in VLAN Mode
FID+SA found in Dynamic MAC Table?
Action
No
Learn and add FID+SA to the Dynamic MAC Address Table
Yes
Update time stamp
Table 11. FID+SA Lookup in VLAN Mode
QoS Priority Support
The KSZ8862M provides Quality of Service (QoS) for applications such as VoIP and video conferencing. Offering four
priority queues per port, the per-port transmit queue can be split into four priority queues: Queue 3 is the highest priority
queue and Queue 0 is the lowest priority queue. Bit 0 of registers P1CR1, P2CR1, and P3CR1 is used to enable split
transmit queues for ports 1, 2, and the host port, respectively.
Port-Based Priority
With port-based priority, each ingress port is individually classified as a high-priority receiving port. All packets received at
the high-priority receiving port are marked as high priority and are sent to the high-priority transmit queue if the
corresponding transmit queue is split. Bit 4 and 3 of registers P1CR1, P2CR1, and P3CR1 is used to enable port-based
priority for ports 1, 2, and the host port, respectively.
802.1p-Based Priority
For 802.1p-based priority, the KSZ8862M examines the ingress (incoming) packets to determine whether they are tagged.
If tagged, the 3-bit priority field in the VLAN tag is retrieved and compared against the “priority mapping” value, as
specified by the register SGCR6. The “priority mapping” value is programmable.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16LF726-E/SO | IC PIC MCU FLASH 8KX14 28-SOIC |
| 0731010340 | BNC JACK VERTICAL PCB 75 OHM |
| V300A5C400BF | CONVERTER MOD DC/DC 5V 400W |
| V300A5C400BL3 | CONVERTER MOD DC/DC 5V 400W |
| PIC16LC620A-04/SS | IC MCU OTP 512X14 COMP 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8862-32MQL | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-32MQL-FX | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-MQL | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support |
| KSZ8863FLL | 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8863FLL-EVAL | 功能描述:以太網開發工具 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。