參數資料
型號： KSZ8862-16MQL-FX
廠商： Micrel Inc
文件頁數： 121/125頁
文件大小： 0K
描述： IC SWITCH ETH 2P 16BIT 128PQFP
標準包裝： 66
系列： KSZ8862
控制器類型： 以太網開關控制器
接口： PCI
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-1638-ND - BOARD EVALUATION KSZ8862-10FL
576-1637-ND - BOARD EVALUATION KSZ8862-100FX
其它名稱： 576-3271
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
95
M9999-040407-3.0
Bank 49 Port 1 PHY Special Control/Status, LinkMD
(0x00): P1SCSLMD
Bit
Default
R/W
Description
Bit is same as:
15
0
RO
Reserved
14-13
0x0
RO
Reserved
12
0
RW
Reserved
11
0
RW
Force_lnk
Force link.
1 = force link pass.
0 = normal operation.
Bank 47 0x02 bit 3
10
1
RW
pwrsave
Power-saving.
1 = disable power saving.
0 = enable power saving.
Bank 47 0x02 bit 2
9
0
RW
Remote (Near-End) Loopback (rlb)
1 = perform remote loopback at Port 1's PHY (RXP1/RXM1 ->
TXP1/TXM1, see Figure 15)
0 = normal operation
Bank 47 0x02 bit 1
8-0
0x000
RO
Reserved
Bank 49 Port 1 Control Register 4 (0x02): P1CR4
This register contains the global per port control for the switch function.
Bit
Default
R/W
Description
Bit is same as:
15
0
RW
LED Off
1 = Turn off all of the port 1 LEDs (P1LED3, P1LED2, P1LED1,
P1LED0). These pins are driven high if this bit is set to one.
0 = normal operation.
Bank 45 0x00 bit 0
14
0
RW
Txids
1 = disable the port’s transmitter.
0 = normal operation.
Bank 45 0x00 bit1
13
0
RW
Restart AN (Note 1)
1 = restart auto-negotiation.
0 = normal operation.
Bank 45 0x00 bit 9
12
0
RW
Disable Far-End-Fault
1 = disable far-end-fault detection and pattern transmission.
0 = enable far end fault detection and pattern transmission.
Bank 45 0x00 bit 2
11
0
RW
Power Down
1 = power down.
0 = normal operation.
Bank 45 0x00 bit 11
10
0
RW
Disable auto MDI/MDI-X
1 = disable auto MDI/MDI-X function.
0 = enable auto MDI/MDI-X function.
Bank 45 0x00 bit 3
9
0
RW
Force MDI-X
1= if auto MDI/MDI-X is disabled, force PHY into MDI-X mode.
0 = do not force PHY into MDI-X mode.
Bank 45 0x00 bit 4
8
0
RW
Far-End Loopback
1 = perform loopback, as indicated:
Start: RXP2/RXM2 (port 2).
Loopback: PMD/PMA of port 1’s PHY.
End: TXP2/TXM2 (port 2).
0 = normal operation.
Bank 45 0x00 bit 14
7
1
RW
Auto Negotiation Enable (Note 1)
Bank 45 0x00 bit 12
相關PDF資料
PDF描述
PIC16LF726-E/SO IC PIC MCU FLASH 8KX14 28-SOIC
0731010340 BNC JACK VERTICAL PCB 75 OHM
V300A5C400BF CONVERTER MOD DC/DC 5V 400W
V300A5C400BL3 CONVERTER MOD DC/DC 5V 400W
PIC16LC620A-04/SS IC MCU OTP 512X14 COMP 20SSOP
相關代理商/技術參數
參數描述
KSZ8862-32MQL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-32MQL-FX 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-MQL 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support
KSZ8863FLL 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863FLL-EVAL 功能描述:以太網開發工具 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*