參數資料
型號： KSZ8862-16MQL-FX
廠商： Micrel Inc
文件頁數： 54/125頁
文件大?。?/td> 0K
描述： IC SWITCH ETH 2P 16BIT 128PQFP
標準包裝： 66
系列： KSZ8862
控制器類型： 以太網開關控制器
接口： PCI
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-1638-ND - BOARD EVALUATION KSZ8862-10FL
576-1637-ND - BOARD EVALUATION KSZ8862-100FX
其它名稱： 576-3271
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
34
M9999-040407-3.0
Table 2 describes the BIU signal grouping.
Signal
Type
(1)
Function
Common Signals
A[15:1]
I
Address
AEN
I
Address Enable
Address Enable asserted indicates memory address on the bus for DMA access and since
the device is an I/O device, address decoding is only enabled when AEN is low.
BE3N, BE2N,
BE1N, BE0N
I
Byte Enable
BE0N
BE1N
BE2N
BE3N
Description
0
32-bit access (32-bit bus only)
0
1
Lower 16-bit (D[15:0]) access
1
0
Higher 16-bit (D[31:16]) access (32-
bit bus only)
0
1
Byte 0 (D[7:0]) access
1
0
1
Byte 1 (D[15:8]) access
1
0
1
Byte 2 (D[23:16]) access (32-bit bus
only)
1
0
Byte 3 (D[31:24]) access (32-bit bus
only)
Note 1: BE3N, BE2N, BE1N and BE0N are ignored when DATACSN is low because 32 bit
transfers are assumed.
Note 2: BE2N and BE3N are valid only for the KSZ8862-32 mode, and are NC for the
KSZ8862-16 mode.
D[31:16]
I/O
Data
For KSZ8862-32 Mode only
D[15:0]
I/O
Data
For both KSZ8862-32 and KSZ8862-16 Modes
ADSN
I
Address Strobe
The rising edge of ADSN is used to latch A[15:1], AEN, BE3N, BE2N, BE1N and BE0N.
LDEVN
O
Local Device
This signal is a combinatorial decode of AEN and A[15:4], The A[15:4] is used to compare
against the Base Address Register.
DATACSN
I
Data Register Chip Select (For KSZ8862-32 Mode only)
This signal is used for central decoding architecture (mostly for embedded application).
When asserted, the device’s local decoding logic is ignored and the 32-bit access to QMU
Data Register is assumed.
INTRN
O
Interrupt
Synchronous Transfer Signals
VLBUSN
I
VLBUSN = 0, VLBus-like cycle.
VLBUSN = 1, burst cycle (both host/system and KSZ8862 can insert wait state)
CYCLEN
I
For VLBus-like access: used to sample SWR when asserted.
For burst access: used to connect to IOWC# bus signal to indicate burst write.
SWR
I
Write/Read
For VLBus-like access: used to indicate write (High) or read (Low) transfer.
For burst access: used to connect to IORC# bus signal to indicate burst read.
SRDYN
O
Synchronous Ready
For VLBus-like access: exactly the same signal definition of nSRDY in VLBus.
For burst access: insert wait state by the KSZ8862M whenever necessary during the Data
Register access.
相關PDF資料
PDF描述
PIC16LF726-E/SO IC PIC MCU FLASH 8KX14 28-SOIC
0731010340 BNC JACK VERTICAL PCB 75 OHM
V300A5C400BF CONVERTER MOD DC/DC 5V 400W
V300A5C400BL3 CONVERTER MOD DC/DC 5V 400W
PIC16LC620A-04/SS IC MCU OTP 512X14 COMP 20SSOP
相關代理商/技術參數
參數描述
KSZ8862-32MQL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-32MQL-FX 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-MQL 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support
KSZ8863FLL 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863FLL-EVAL 功能描述:以太網開發工具 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*