參數資料
型號： KSZ8851-16MQL
廠商： Micrel Inc
文件頁數： 42/88頁
文件大小： 0K
描述： IC CTLR MAC/PHY NON-PCI 128-PQFP
產品培訓模塊： KSZ8851 10/100 Embedded Controllers
標準包裝： 66
控制器類型： 以太網控制器，MAC/PHY
接口： 總線
電源電壓： 1.8V，2.5V，3.3V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-3292-ND - BOARD EVALUATION KSZ8851-16MLL
其它名稱： 576-3253
PIC16F8X
DS30430C-page 48
1998 Microchip Technology Inc.
8.9
Interrupts
The PIC16F8X has 4 sources of interrupt:
External interrupt RB0/INT pin
TMR0 overflow interrupt
PORTB change interrupts (pins RB7:RB4)
Data EEPROM write complete interrupt
The interrupt control register (INTCON) records
individual interrupt requests in flag bits. It also contains
the individual and global interrupt enable bits.
The global interrupt enable bit, GIE (INTCON<7>)
enables (if set) all un-masked interrupts or disables (if
cleared) all interrupts. Individual interrupts can be
disabled through their corresponding enable bits in
INTCON register. Bit GIE is cleared on reset.
The “return from interrupt” instruction, RETFIE, exits
interrupt routine as well as sets the GIE bit, which
re-enable interrupts.
The RB0/INT pin interrupt, the RB port change interrupt
and the TMR0 overflow interrupt flags are contained in
the INTCON register.
When an interrupt is responded to; the GIE bit is
cleared to disable any further interrupt, the return
address is pushed onto the stack and the PC is loaded
with 0004h. For external interrupt events, such as the
RB0/INT pin or PORTB change interrupt, the interrupt
latency will be three to four instruction cycles. The
exact latency depends when the interrupt event occurs
(Figure 8-17). The latency is the same for both one and
two cycle instructions. Once in the interrupt service
routine the source(s) of the interrupt can be determined
by polling the interrupt flag bits. The interrupt flag bit(s)
must be cleared in software before re-enabling
interrupts to avoid infinite interrupt requests.
FIGURE 8-16: INTERRUPT LOGIC
Note 1: Individual interrupt flag bits are set
regardless
of
the
status
of
their
corresponding mask bit or the GIE bit.
RBIF
RBIE
T0IF
T0IE
INTF
INTE
GIE
EEIE
Wake-up
(If in SLEEP mode)
Interrupt to CPU
EEIF
相關PDF資料
PDF描述
LTC4278CDKD#PBF IC PD IEEE 802.3AT 25.5W 32-DFN
KSZ8873MLL IC ETHERNET SWITCH 3PORT 64-LQFP
KSZ8863RLL IC ETHERNET SW 3PORT 48-LQFP
KSZ8863MLL IC ETHERNET SW 3PORT 48-LQFP
KSZ8863FLL IC ETHERNET SW 3PORT 48-LQFP
相關代理商/技術參數
參數描述
KSZ8851-16MQL-EVAL 功能描述:以太網開發工具 Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free) Eval Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8851-16MQLI 功能描述:以太網 IC Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free, I-Temp) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8851-32MQL 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with Generic (32-bit) Bus Interface, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8851-32MQLI 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with Generic (32-bit) Bus Interface (I-Temp) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8851MLL 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Single Port MAC/PHY Controller with Non PCI Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*