參數資料
型號： ISP1501
英文描述： Hi-Speed Universal Serial Bus peripheral transceiver
中文描述： 高速通用串行總線外設收發器
文件頁數： 34/40頁
文件大?。?/td> 770K
代理商： ISP1501
Philips Semiconductors
ISP1501
Hi-Speed USB peripheral transceiver
Product data
Rev. 02 — 21 November 2002
34 of 40
9397 750 10025
Koninklijke Philips Electronics N.V. 2002. All rights reserved.
21. Soldering
21.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended.
21.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferable be kept below 220
°
C for thick/large
packages, and below 235
°
C small/thin packages.
21.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
相關PDF資料
PDF描述
ISP1520 Hi-Speed Universal Serial Bus hub controller
ISP1520BD Hi-Speed Universal Serial Bus hub controller
ISP1521 Hi-Speed Universal Serial Bus hub controller
ISP1521BE Hi-Speed Universal Serial Bus hub controller
ISP1561 ISP1561BM
相關代理商/技術參數
參數描述
ISP1501BE 制造商:PHILLIPS 功能描述:
ISP1504 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hi-Speed USB OTG(On-The-Go) Transceiver
ISP1504A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ULPI Hi-Speed Universal Serial Bus On-The-Go transceiver
ISP1504A1_07 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ULPI Hi-Speed Universal Serial Bus On-The-Go transceiver
ISP1504A1ET 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ULPI Hi-Speed Universal Serial Bus On-The-Go transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*